User manual DRAKE DIGITAL SCTECI
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual DRAKE DIGITAL SCTECI. We hope that this DRAKE DIGITAL SCTECI user guide will be useful to you.
Manual abstract: user guide DRAKE DIGITAL SCTECI
Detailed instructions for use are in the User's Guide.
[. . . ] SCTeci Ethernet Control Interface
Instruction Manual
TM is a trademark of the R. L. Drake Company
P/N: 3852392B-01-2008
Printed in U. S. A.
2
Caution Statements
WARNING: TO PREVENT FIRE OR ELECTRICAL SHOCK DO NOT EXPOSE TO RAIN OR MOISTURE
A product and cart combination should be moved with care. Quick stops, excessive force and uneven surfaces may cause the product and cart combination to overturn. The lightning flash with arrow head symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] (See illustration at left. ) See note on page 11 if FTP file transfer was used. No radio buttons will be displayed if SCT860 entries are selected since they do not have internally programmed serial numbers.
Note that once a link is established, "Link is Active" followed by the SCTeci IP number will appear on the SCTeci display, and all front panel buttons except RESET will be locked out. Note: Allow ten seconds between stopping or closing one logged on screen and attempting to log on again.
OPERATION (contnued)
MODIFYING TRANSCODER PARAMETERS To modify parameters of any monitored transcoder, you must first do one of the following: 1) From the select mode menu, select 'single SCT860', or 'PS15x Transcoder'. OR 2) Select any of the SCT860 or PS15x entries that have active transcoders. Then press the 'View/Edit' button beneath the data for the selected transcoder. Either of these actions will produce a screen similar to the one shown below which will contain the changeable parameters for the selected transcoder.
9
ENTERING OR CHANGING SCT PASSWORD If the transcoders being accesssed have been set to require a password, this SCT password must be entered into the SCTeci. 1) Click on the down arrow on the 'Select Mode:' window, and choose 'Select SCT Password' from the resulting drop down menu. This will produce a screen similar to below.
Type desired password here.
1) Pressing the down arrow for a selected parameter will produce a drop down menu which will give the available choices. 3) On items which have no down arrow, the desired parameters can be typed in directly. 4) Once you have changed all the parameters to your satisfaction, press the 'APPLY' button. The top cell of the 'Status' table on the upper right corner of the display will show one of the following error messages: Search; Out of Lock; Out of range; QAM Version; Demod error; or if there are no errors, signal to noise ratio (SNR). The selection box in the upper left hand corner of this window allows selection of the displayed parameters for any other transcoder attached through PS15x power supplies. The 'Block of 10' button will produce a table which will show all 10 transcoders in the group containing the transcoder displayed in the box.
2) Type the desired SCT transcoder password into the box as shown in the above illustration. 3) If the password in the SCTs needs entered or changed, someone at the SCT transcoder location must simultaneously hold down the left, center, and right buttons on each SCT860 or PS151 for at least two seconds. This will cause 'LOADING PASSWORD' to appear on the SCT transcoder's display. Do this on each transcoder or power supply that needs the new password loaded. If being remote controlled solely with the SCTeci, a password of 0 should be entered. 'LOADING PASSWORD' will disappear from the SCT transcoder's display and the new password will be loaded. PRESET CHANNELS The preset channels function allows you to add to, modify, or delete the selections that are available in the Demod Mode selection window which appears when programming individual SCTxxxx transcoders. To access this function, select 'Preset Channels' from the Select Mode drop down menu. You will be presented with a screen similar to the following:
Note that the exact appearance of the screens shown here will vary depending upon the web browser used, and to the PC display resolution selected. In the above window, Internet Explorer V6 was used with a screen resolution of 800 x 600 pixels.
Notice the 'Group' window on the left and the 'Add New Channel', 'Edit Channel', and 'Delete Channel' buttons at the bottom of the channels window.
10
Operation (continued)
Deleting a Channel 1) From the Preset Channels screen, select the group and channel that you wish to delete. [. . . ] The unit must be sent to the following address: Service Department R. L. Be sure to include your street address which will be needed for UPS return. UPS Surface (Brown Label) takes 7-10 days to reach us depending on your location, Blue takes 2-3 days.
Red is an overnight service. Send the unit in a way that it can be traced if we can't verify receipt of shipment. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE DRAKE DIGITAL SCTECI
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual DRAKE DIGITAL SCTECI will begin.