User manual DSC PC4000

[. . . ] Jan 11, 1993 Software Version 1. 3 INSTRUCTION MANUAL PC4OOO SECURITY SYSTEM DOC NOTICE NOTICE: The Canadian Department of Communications label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements. The Department does not guarantee the equipment will operate to the user's satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. [. . . ] Smoke Detector Loop Trouble. . . If a FIRE loop is open circuit, a keypad trouble and a Fire Loop trouble transmission are generated. A trouble on the FIRE loop will unconditionally initiate an audible indication on the keypad. This means that even if any other previous trouble has been silenced, a FIRE loop trouble will restart the keypad buzzer. Loss of Internal Time. . . When the PC4000 is powered up, the internal time of day clock needs to be set to the correct time. 4204 Battery TBL. . . If any PC4204 relay output module's battery drops below 11. 3 volts, a battery trouble is generated. So the battery trouble may not restore instantly when the battery voltage is restored. 4204 AC Trouble. . . If any PC4204 relay output module loses incoming AC power, the keypad trouble light will indicate a 4204 AC trouble. But there will be no audible annunciation until there is also a low battery condition. 4204 AUX Trouble. . . If the Aux fuse on any PC4204 relay module should open or if the Aux supply is overloaded, a 4204 Aux trouble is generated. 5 ALARM MEMORY DISPLAY []+[3] Press [] then [3] to enter the alarm memory mode. The "Alarm Memory" message will only be displayed when an alarm occurred during the last armed period. Press [#] to return to "READY". USER FUNCTIONS COMMAND []+[6]+[ACCESS CODE] Enter [][6][Access Code] and then use the [<][>] keys to display the items of the function menu. [0] Quick Arm [1] Quick Exit [2] Auto Arm Control [3] Keypad Setup [4] Bell/Comm Test [5] Door Chime [6] Spec. Messages [7] User Call Up [8] View Partitions Item [0], [1], [5] and [6] turn on and off various functions. To enable or disable these functions, press the [] key to toggle "Y "or "N" on the keypad. Y - The function is enabled N - The function is disabled QUICK ARM []+[6]+[ACCESS CODE]+[0] The "Quick Arm" feature is enabled by toggling to "Y" on the keypad. One time use access codes should not be used with the quick arm feature. QUICK EXIT []+[6]+[ACCESS CODE]+[1] The "Quick Exit" function is enabled by toggling to "Y" on the keypad. When enabled the user can exit through any delay zone without altering the status of the system, by entering [][0] on the keypad. AUTO ARM CONTROL []+[6]+[ACCESS CODE]+[2] This function must be enabled by the installer, or an error tone will sound when this section is entered. The PC4000 can be programmed to arm a partition at the same time each day, by enabling the Auto Arm function and programming the Auto Arm time. The keypad begins to sound and the Bell/Siren will pulse once every 10 seconds to alert anyone on the premises that the system is about to arm. [. . . ] neither assumes, nor authorizes any other person purporting to act on its behalf to modify or to change this warranty, nor to assume for it any other warranty or liability concerning this product. be liable for any direct or indirect or consequential damages, loss of anticipated profits, loss of time or any other losses incurred by the buyer in connection with the purchase, installation or operation or failure of this product. recommends that the entire system be completely tested on a regular basis. However, despite frequent testing, and due to, but not limited to, criminal tampering or electrical disruption, it is possible for this product to fail to perform as expected. 10 APPENDIX A LIST OF AVAILABLE ASCII CHARACTERS 032 048 064 080 096 112 160 176 192 208 224 240 033 049 065 081 097 113 161 177 193 209 225 241 034 050 066 082 098 114 162 178 194 210 226 242 035 051 067 083 099 115 163 179 195 211 227 243 036 052 068 084 100 116 164 180 196 212 228 244 037 053 069 085 101 117 165 181 197 213 229 245 038 054 070 086 102 118 166 182 198 214 230 246 039 055 071 087 103 119 167 183 199 215 231 247 040 056 072 088 104 120 168 184 200 216 232 248 041 057 073 089 105 121 169 185 201 217 233 249 042 058 074 090 106 122 170 186 202 218 234 250 043 059 075 091 107 123 171 187 203 219 235 251 044 060 076 092 108 124 172 188 204 220 236 252 045 061 077 093 109 125 173 189 205 221 237 253 046 062 078 094 110 126 174 190 206 222 238 254 047 063 079 095 111 127 175 191 207 223 239 255 FCC COMPLIANCE STATEMENT CAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd. [. . . ]