User manual DURKOPP 911

[. . . ] 911 CNC-controlled sewing unit with large sewing area Operating Instructions Installation Instructions Service Instructions 1 2 3 Postfach 17 03 51, D-33703 Bielefeld Potsdamer Straße 190, D-33719 Bielefeld Telefon +49 (0) 5 21/ 59 25-00 Telefax +49 (0) 5 21/ 9 25 24 35 www. duerkopp-adler. com Ausgabe / Edition: 08/2010 Änderungsindex Rev. index: 00. 0 Printed in Federal Republic of Germany Teile-Nr. /Part. -No. : 0791 911001 All rights reserved. Reproduction or publication of the content in any manner, even in extracts, without prior written permission of Dürkopp Adler AG, is prohibited. Copyright © Dürkopp Adler AG - 2010 Foreword This instruction manual is intended to help the user to become familiar with the machine and take advantage of its application possibilities in accordance with the recommendations. [. . . ] -> Sequence A new sequence will be generated. 1 ­ ­ ­ Tip onto the desired sewing program. The sewing program is adopted and will be displayed in the sequence field. Insert additional sewing programs. 25 ­ ­ ­ ­ Tip onto the button "Set name". The sequence will be memorized. 26 7. 6. 3 Opening a sewing program or a sequence Via this menu item, sewing programs or sequences can be opened from the DAC and then be sewn. ­ Click File -> Open The following screen will appear: 1 ­ Click "File filter". The file filter will be opened. According to the selection the following will be displayed: · · · All files Seam programs (. fnp911) Sequences (. seq911) 27 7. 6. 4 Copying a sewing program, a sequence or machine parameters Via this menu item it is possible to copy sewing programs, sequences or machine parameters onto the DAC control or onto a USB-Stick. Click File -> Copy The following screen will appear: ­ ­ ­ Select where to copy from: - from the DAC control unit to an USB-stick or - from an USB-stick to the DAC control unit Tip on the sewing program or sequence to be copied. The selected program will be copied. 7. 6. 5 Deleting a sewing program or a sequence Via this menu item, sewing programs or sequences can be deleted from the DAC. ­ Click File -> Delete The following screen will appear: ­ ­ Tip on the sewing program or sequence to be deleted. The program or the sequence will be deleted. 28 7. 7 Menu item "Edit" 7. 7. 1 Editing a sewing program A sewing program consists of a contour and sewing parameters. The contour (shape of seam) is created via Teach-in or with the help of the DA-CAD 5000. The program parameters are divided into different groups and are modified as follows: ­ Click Edit -> Seam program -> Parameters The following screen will appear: 1 PP1 - Configuration Seam name max. = 10. 0 mm ) Limits the programmable foot height to this value so that with thicker material only this value has to be adjusted. Adjust the thread tension (min. = 100%) The thread tension profile of the whole contour will be adjusted according to the percentage value. = 100%) The run speeds will be adjusted accordingly. Clamp ID-Code Barcode (ID-Code) max. 10 characters for a security check before the sewing start (the optional equipment barcode reader has to be activated) 29 Laser marking lamps Up to four laser marking lamps can be triggered in order to facilitate the aligning of the material (The optional equipment has to be activated) Needle reverse turn mode The following modes can be set: Not active The needle remains in the stopping position. After the complete contour After the completion of all the seams of a contour the needle is turned back to the set value (MP parameter). After each seam (def. ) After each seam the needle will be turned back. PP2 - Load mode Feeding mode The following modes can be set: Mode 1 (def. ) The clamp will be opened in the feeding position. After actuating the pedal the left part of the two-piece clamp for an angular feed will be closed. After actuating the pedal one more time the right side will be closed. After actuating the pedal the right part of the two-piece clamp for an angular feed will be closed. [. . . ] The menu for the seam parameters will pop up. ­ ­ ­ Enter the seam parameters for the new seam segment. Enter the desired seam segment by using the arrow keys "ñ" , "ò" , "ñ" or "ò". Enter all further seam segments. Step 3 ­ ­ Press the "Memorize" button. After a successful test the seam can be sewn. 54 7. 12 Repair mode Via this button the repair mode can be called up. [. . . ]