User manual EARLEX COMBIPOWERVAC

[. . . ] Never use power tools rated at more than 1800W in the power take off socket. Always be aware of the direction of the blow outlet or deflector elbow when using the unit. Use only genuine Earlex replacement parts. Due to the heavy duty nature of a wet & dry cleaner the motor may sound louder than your normal cleaner. In order to be able to pick up liquids, a special by-pass motor is fitted so that the liquid can be deposited into the recovery tank without going through the motor. [. . . ] 1) Ensure that the motor housing has been clipped onto the base in the correct position, with the air outlet opposite the vacuum inlet hose. Failure to observe this will allow the filter to foul the internal inlet pipe. CLEANING THE FILTER DUST COLLECTION BAG ASSEMBLING THE HOSE OPERATION 3) The unit has two operating modes - continuous and power take off mode. With the switch set to position I (continuous mode) the vacuum motor will operate all the time that the switch is on. SWITCH POSITIONS 4 2) Unwind the mains lead fully and connect to the mains or extension lead. With the switch in position II (power take off mode) the operation of the vacuum motor is controlled by a power tool plugged into the socket on the back of the unit. When the power tool is switched on there is a delay of approximately 5 seconds before the vacuum motor switches on. When the power tool is switched off there is a delay of approximately 7 seconds before the vacuum motor switches off. The cleaner is protected by an automatic shut-off float valve when it becomes full of liquid. This will become apparent to you as the motor will start to make a high pitched noise. 3) Lift the hose up to drain any excess liquid back into the container. 5) Try to keep the hose raised whilst emptying out the liquid, this can help eliminate any spills. WARNING - BE CAREFUL WHEN EMPTYING THE TANK - IT MAY BE HEAVIER THAN YOU THINK. FLOAT SHUT OFF Important The float valve is a safety device, do not attempt to remove this or modify it, it is there for your safety. Should the cleaner overturn during use, switch the unit off immediately, return to the upright position and wait until the float valve has repositioned itself. If collecting soapy water you will need to regularly check whether the unit requires emptying as the lather can bypass the float system and there can be a discharge of foam!Should this occur switch off the unit, wash out any foam in the filter and tip away any water around the outlet on the motor housing, before restarting. WARNING - TAKE CARE, THE TANK MAY BE HEAVIER THAN YOU THINK. 3) Empty tank of all contents - making sure that you are protected against any sharp objects. 1) The CombiPowerVac can be used as a powerful blower by inserting the hose into the outlet on the motor housing. 2) Always ensure that the hose, tank and accessories have been cleaned of any debris before operating the blower function. 3) You should always protect your eyes with safety goggles when using this function and ensure that no one else is in close proximity. 4) Uses include: blowing leaves into piles, blowing out dust from difficult to get to areas, faster drying of paint. The blower function is also used to power the Combispray Gun which is available as an optional extra. WDACC18 Note - Always switch the unit off before changing between vacuum and blower functions. TM EMPTYING TANK BLOWER FUNCTION To assemble the floor head, offer the brush/squeegee head up to the body and when securely in place, clip the securing lock tabs into place with a firm finger pressure. To release, unclip by applying a firm finger pressure in an outwards direction. Do not under any circumstances use tools such as pliers or a screwdriver as you may damage the product. If required, the brush/squeegee head can be cleaned with warm soapy water. FLOOR HEAD ASSEMBLY 5 The unit is supplied with a stepped power tool adaptor to fit the exhaust port of many sanders, planers and jigsaws. [. . . ] It has a 1 litre capacity, easy-grip handle that provides good balance and control. Check the Earlex website for up to date information on what you can spray. Spray Station - HVLP (High Volume Low Pressure) Complete paint spraying system - Ideal for spraying large or detailed jobs with equal ease. Fast and easy, provides a quality finish with no unsightly brush marks. The Spray Station can spray many types of paint, such as stains, varnishes, emulsion, glazes, wood treatments and many more. PRA1 1. 4m Extension Pole - Used in conjunction with the PR9 the PRA1 allows you to paint ceilings and high areas without the use of step ladders or having to move furniture. Your attention is brought to new directives applicable to the disposal of this electrical equipment, where in accordance with the legislation this product must not be disposed of in your normal household waste. [. . . ]