User manual ELECTROLINE SUMMIT 3208GLD

[. . . ] Summit 3208GLD Installation, Operation and Programming Electronics Line (E. L. ) Ltd. www. elecline. com E L E C T R O N I C S L I N E ' S T E C H N I C A L S U P P O R T D E P A R T M E N T : (972)-3-9211110 Electronics Line (E. L. ) Ltd. reserves the right to change the information within this manual without prior notice. ZI0084A (12/98) 2 TABLE OF CONTENTS Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 About the Summit 3208GLD Installation, Operation and Programming Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Publication Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Chapter One: Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1. 1: Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Pressing MENU/NEXT or entering data moves the cursor to the next parameter digit. To move to another item within the current group, press SELECT and then MENU/NEXT or Q to scroll forwards and backwards through the available options. For example, if zone 1 is selected, the zone number flashes when SELECT is pressed. MENU/NEXT and Q enable you to scroll forward and backwards through the zones. For the modifications to take effect, disconnect and reconnect both AC and battery power supplies. Note: The system allows two minutes to begin programming before automatically exiting programming mode. Programming mode is immediately aborted if the control panel is in communication (both incoming and outgoing calls). LCD Keypad Programming Display Entering programming mode SELECT ADDR : 0 0 0 (000 - 499) First digit blinking, any key will change this digit Press: Q to move to the previous digit SELECT to select another address or group of parameters MENU/NEXT to move to the next digit or group AWAY to exit programming mode 23 After entering parameter changes Parameter address Group ID ADDR: 000 ZONE 01 VAL=> 58 08 12 05 First digit blinking Upon entering a digit, the display automatically moves to the next digit. To move to the next digit without entering a modification, press MENU/NEXT. Entering Hex data Pressing # scrolls through the hexadecimal digits A, B, C, D, E and F. If the original digit is decimal (0-9), press # to change the digit to A. If the original digit is hexadecimal (A-F), press # to move to the next hexadecimal digit in sequence. 4. 4: Programming Parameters This section comprises a complete listing of the Summit 3208GLD control panel's programming parameters. The following table lists the addresses for each group of programming parameters. ADDRESSES 000-127 128-131 132-139 140-179 180-195 196-197 198-201 202-261 262-295 296-310 PARAMETERS Zone Parameters System Parameters Keypad Parameters Telephone Numbers Account Numbers Telephone Line Parameters Communication Protocols Zone Oriented Event Codes Event Oriented Event Codes Event & Message Routing ADDRESSES 388 389-409 410 411 412-475 476 477-490 491-493 494 495 PARAMETERS Swinger Parameters Opening & Closing Windows Bell Cut-Off Dealer Lockout & Latchkey Custom LCD Zone Descriptors Zone Expanders Relay Parameters Periodic Test Arming Options & Arming Ring Detailed Display, Bell Muting & Fire Sensor Reset Police Key Operation & RP Communication Options AC Loss & Restore Listen-In Time Out 378-381 Exit Timers 496 382-384 385-387 Entry Timers Pulse Counters 497-498 499 24 ADDRESSES 000-127: ZONE PARAMETERS 000-003: Zone # 1 Parameters Each zone is individually defined in four parameter addresses. The following four addresses relate to zone 1 but the method of programming zones 2 - 32 is identical. 000 LCD Zone Descriptor and Entry Delay for Zone #1 Select a zone descriptor and entry delay for zone 1 from the table below. Entry delay options #1, #2 and #3 are set at addresses 382, 383 and 384, respectively. The four custom LCD messages can be programmed at addresses 412-475. Delay #1 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4E 4F 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5D 5E 5F Delay #2 80 81 82 83 84 85 86 87 88 89 8A 8B 8C 8D 8E 8F 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9E 9F Delay #3 C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF no message 1ST FLOOR 2ND FLOOR 3RD FLOOR 4TH FLOOR BACK DOOR BASEMENT BATHROOM BEDROOM BEDROOM 1 BEDROOM 2 BEDROOM 3 COMPUTER CONFERENCE CORRIDOR DINING DOOR EAST EMERGENCY ENTRANCE EXIT EXTERIOR FAMILY FIRE FRONT DOOR GARAGE GUEST ROOM HALL HOLDUP INTERIOR KITCHEN LAUNDRY Descriptor No Delay 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F Delay #1 60 61 62 63 64 65 66 67 68 69 6A 6B 6C 6D 6E 6F 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 7F Delay #2 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF Delay #3 E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF LOBBY LIVNG ROOM MSTR BEDRM MAT MOTION NORTH NURSERY OFFICE PANIC PERIMETER POOL ROOF ROOM ROOM 1 ROOM 2 ROOM 3 ROOM 4 SHIPPING SHOP SLIDE DOOR SOUTH STAIRS STORAGE STUDY VAULT WAREHOUSE WEST WINDOW (custom #1) (custom #2) (custom #3) (custom #4) Descriptor No Delay 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 25 001 First Digit: Loop Speed, Pulse Count and Swinger Setting for zone # 1 The following table lists the options for the loop speed, pulse count and swinger setting. A slow loop response (150ms) should be entered for motion sensors and contacts. The three optional pulse count settings can be programmed at addresses 385-387 and the swinger setting is programmed at address 388. A full explanation of these features can be found in this section at their respective addresses. First digit value: Loop Pulse Swinger Value Loop Pulse Swinger Value Speed Count Setting Speed Count Setting None 0 None 8 Active 1 Active 9 #1 2 #1 A Slow Active 3 Fast Active B #2 4 #2 C Active 5 Active D #3 6 #3 E Active 7 Active F Second Digit: Bypassability, Zone Chime and System ID The second digit of this address deals with a number of options. Select whether the zone is bypassable, if the zone chime feature is enabled and to which system the zone is assigned from the table below. [. . . ] AND ITS SUBSIDIARIES (EL) warrants its products to be free from manufacturing defects in materials and workmanship for two years following the date of sale. EL will, within said period, at its option, repair or replace any product failing to operate correctly without charge to the original purchaser or user. In case of defect, contact the security professional who installed and maintains your security system. In order to exercise the warranty, the product must be returned by the user or purchaser, shipping costs prepaid and insured to EL. [. . . ]