User manual ELICA GRACE

[. . . ] 17 EN - Instruction on mounting and use Closely follow the instructions set out in this manual. All responsibility, for any eventual inconveniences, damages or fires caused by not complying with the instructions in this manual, is declined. It is important to conserve this booklet for consultation at any moment. In the case of sale, cession or move, make sure it is together with the product. [. . . ] Side light check (when scheduled) The side lights may be switched on and off by pressing AND HOLDING DOWN the T2 button on the control panel. HOLDING DOWN the button, besides permitting to switch the hood on and off, it also regulates the light intensity given from the lights. note: The switching on and off functions (and regulating function) alternate. The regulation of the light intensity is not available for hoods with neon lights. Reset and configuration for filter saturation signal Switch on hood to any speed (see above paragraph “Suction speed (power) selection”) Reset grease filter saturation signal (FLASHING GREEN LIGHT on control panel) First proceed with filter maintenance as described in corresponding paragraph. Press and hold down (for more than 3 seconds) the T1 button on the control panel, the LED light will stop flashing indicating that the signal reset has been carried out, the hood will switch off. reset coal filter saturation signal (FLASHING ORANGE (amber) LED light) First proceed with filter maintenance as described in corresponding paragraph. Press and hold down (for more than 3 seconds) the T1 button on the control panel, the LED light will stop flashing indicating that the signal reset has been carried out, the hood will switch off. Coal filter saturation signal disactivaction (for particular applications) Switch off hood (see above paragraph “suction speed (power) selection”). Press and hold down (for more than 5 seconds) the T1 button on the control panel, the LED light will start flashing GREEN indicating that the coal filter saturation signal has been disactivated. In order to reactivate the coal filter saturation signal, repeat operation, the LED light will flash ORANGE (amber) Command panel disassembly. Extract command panel by lifting it with a small screwdriver or similar tool. 23 Using the remote control The remote control is able to control all the functions of the hood: Select the suction speed (power) Control the central light Control the lateral lights Reset e configure the saturation of the filters signal Selecting the suction speed (power): Press the "◄" key or the "►" key until you see the symbol relating to the “Select the suction speed (power)” function. Press the “+” key or the “-” key or the "■" key respectively to increase or diminish or switch off (stand-by) the speed (suction power). Controlling the central light: Press the "◄" key or the "►" key until seeing the symbol relating to the “Controlling the central light” function on the remote control. Press the “+” key or the “-” key respectively to switch the central light (ON) or (OFF). Press the "■" key to change the state of the light from (OFF) to (ON) or vice versa. Controlling the lateral lights: Press the "◄" key or the "►" key until seeing the symbol relating to the “Controlling the lateral lights” function on the remote control. Press the "■" key to change the state of the lateral lights from (OFF) to (ON) at maximum intensity and viceversa. Press the “-” key to diminish the intensity of the lateral lights until switching them off. Press the “+” key to increase the intensity of the lateral lights. Resetting and configuring the saturation of the filters signal Switch the hood on at any speed (see paragraph above “Selecting the suction speed (power”). [. . . ] Repeter operasjonen for å aktivere signalet for mettet kullfilter igjen. 23 Bruk av fjernkontrollen Fjernkontrollen er i stand til å kontrollere alle ventilatorhettens funksjoner: Valg av sugehastighet (styrke) Kontroll av hovedlyset Kontroll av sidelysene Reset og konfigurasjon av signaleringen for skitne filtre Valg av sugehastighet (styrke): Trykk på knappen "◄" eller "►" helt til du ser funksjonssymbolet for “Valg av sugehastighet (styrke) på fjernkontrollen. Trykk på knappen “+” eller “-” eller "■" for å øke eller minske hastigheten, eller for å slå av viften (stand by). Reset og konfigurasjon av signaleringen for skitne filtre Slå på ventilatorhetten i en hvilken som helst hastighet (se avsnittet ovenfor: “Valg av sugehastighet (styrke)”) Trykk på knappen "◄" eller "►" helt til du ser funksjonssymbolet “Reset og konfigurasjon av signaleringen for skitne filtre” på fjernkontrollen. [. . . ]