User manual ENEO NT-MANAGER

[. . . ] User's Manual NT-Manager 16Channel Please read this manual thoroughly before use, and keep it handy for future reference. Design and specifications are subject to change without notice. Table of Contents 1. Introduction of Program. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2. Preparations before operating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2. 1 Minimum System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2. 2 Installing NT-Manager Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2. 3 Network Device IP Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2. 3. 1 IP setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2. 3. 2 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3. [. . . ] Up to four videos can be played at one time and the videos can be observed in the 1-screen or 4, 8, 11, 16-screen split mode, or in the full screen mode. You can easily move to the desired time position using the record information bar. 18 -Make Clip File 1. *Click "Estimation" button, eVideoClient show video clip file size. Run screens of ClipViewer. Save: Current screen save to image file. 20 5. 4. 5 System log This shows important events occurring during the program operation in real-time. Up to 1000 system logs can be saved, and old-dated logs are deleted from the program automatically. 5. 4. 6 Camera status Alarm Event Alarm Event status When an alarm input event occurs, the alarm icon, located at upper right of the screen, blinks for the time period set in the network device setting. *Refer to `7. 1. 4 Alarm Setup', `7. 1. 5 Event Setup' for details on the Alarm, Event setting. Motion Event Motion Event status When a motion event occurs, the motion icon, located at upper right of the screen, blinks for the time period set in the network device setting. *Refer to `7. 1. 3 Motion Setup' for details on the motion setting. Recording Recording on/off status In order to save the real-time observation video to PC, press the recording button. The realtime observation video current shown is recorded and saved to PC. For the method of recording, search and playback, please see the `6 Record/Search/Replay Video. ' 21 Audio Control Microphone on/off status Speaker on/off status If users are to control the volume of a microphone and speaker connected to a user PC, they should adjust the user PC volume regardless of the microphone and speaker volume control set in Network Devices. · Full Down Menu Check this item when showing control panel. The control panel to hidden, Uncheck the button once again. 5. 5 Program information Click this item to see program information. · Toolbar · Full Down Menu 22 5. 6 Program Exit Click this item to see program Exit. Record Record an image under real-time monitoring to the HDD of users PC. 6. 1 Manual Recording When clicking the recording button during the real-time observation, the color turns to red and the recording starts. When pressing the recording button again, this recording process will stop. · Toolbar · Full Down Menu · On Screen 23 6. 2 Motion Event Recording If a motion event occurs, it can be recorded automatically through this setting process. For motion event recording, execute the motion event setting (See the"7. 1. 3 Motion Setup"), and try the record setting (See the "7. 1. 9 Record Setup"). 6. 2 Alarm Event Recording If an alarm event occurs, it can be recorded automatically through this setting process. For alarm event recording, execute the alarm event setting (See the "7. 1. 4 Alarm Setup"), and try the record setting (See the "7. 1. 9 Record Setup"). · Record Mode Overwrite record mode Record once mode Before recording, check the remaining amount and the recording course and the overwrite item of the hard disk. Setup 7. 1 Setting up Network Device Currently the setup window which corresponds to the network equipment which is connected appears. · On Screen · Setup Window (pop up) 24 7. 1. 1 Video Setup Image Appearance Resolution It enables users to determine a basic screen size when having an access through the Web Browser or PC program. [. . . ] Check Box: When the record file is full, show message. Language Language options are: English, French, German, Spanish, Russian, Japanese and Italian. OSD Enable OSD Text Check this item when showing an information of Network Device name and channel number etc. 47 7. 2. 4 System3 Setup Popup window When the event occurs in popup window shows. Set up NT-Manager Client to sound when events are detected by selecting events from the list and designating the sound file (. wav) path. Select event type Alarm and Motion. 48 7. 2. 5 Favorite Setup Favorite The Favorite is a user-defined connection list that combines more than one remote site, so multiple sites can be monitored at the same time with a single connection. [. . . ]