User manual EPSON FX-2190

[. . . ] ® 9-pin Dot Matrix Printer User's Guide This manual is divided in two sections: English and Spanish. Este manual está dividido en dos secciones: Inglés y Español. El manual en español comienza aproximadamente a la mitad del libro. El manual en inglés comienza después de esta página. All rights reserved. [. . . ] The loading procedure for continuous paper with labels is the same as that for ordinary continuous paper, except you must set the paper-thickness lever to 2 before printing. Note: It is best to load continuous paper with labels on the pull tractor. Never feed labels backward using the Load/Eject or Tear Off/Bin button. When fed backward, labels can easily peel off the backing sheet and cause a paper jam. Because labels are sensitive to temperature and humidity, use them only under normal operating conditions: Temperature Humidity 59 to 77°F (15 to 25°C) 30 to 60% RH Do not leave labels loaded in the printer between jobs; they may curl around the platen and jam when you resume printing. 28 Paper Handling Do not load continuous paper with labels from the rear paper slot. Because the rear paper path is curved, labels may come off their backing sheets inside the printer and cause a paper jam. Do not load paper that is curled or has been folded. Removing continuous paper with labels To prevent labels from peeling off the backing sheet and jamming the printer, follow these steps to remove continuous paper with labels from the printer: 1. Tear off the fresh supply of continuous labels at the perforation nearest the paper entry slot. Hold down the LF/FF button to eject the remaining labels from the printer. c Caution: labels backward using the Load/Eject or Tear Off/Bin button. Never feed When fed backward, labels can easily come off the backing sheet and cause a paper jam. Envelopes You can feed envelopes one at a time using the paper guide, or you can load multiple envelopes using the optional high-capacity cut-sheet feeder (bin 1 of the double-bin cut-sheet feeder). Before loading envelopes, set the paper-thickness lever to position 5 (for thin envelopes) or 6 (for thick envelopes). To load single envelopes, follow the instructions in "Loading Single Sheets with the Paper Guide" on page 26. Note: Be sure to place the envelope printable side down and insert the top edge of the envelope into the printer first. Paper Handling 29 The print head must not print past the left or right edge of the envelope or other thick paper. Make sure your application program prints entirely within the printable area of your envelope. See "Printer Specifications" in the Reference Guide for more information on the printable area of envelopes. 6 envelopes, make sure the left edge guide is aligned with the arrow on the paper guide. Postcards You can feed postcards one at a time using the paper guide, or you can load multiple cards using the optional high-capacity cut-sheet feeder (bin 1 of the double-bin cut-sheet feeder). Before loading postcards, set the paper-thickness lever to position 2 and set the paper release lever to the single-sheet position. To load a single card, follow the instructions in "Loading Single Sheets with the Paper Guide" on page 26. Note: When you are loading postcards long edge first, always load them in the top slot. Before printing, turn on the card mode by pressing the Tear Off/Bin button several times until the left Tear Off/Bin light is on. When loading A6 size cards, always load them long edge first. 30 Paper Handling Using the Micro Adjust Function The Micro Adjust function allows you to move the paper forward or backward in 1/216-inch (0. 118 mm) increments to adjust the tear-off and top-of-form positions. Adjusting the tear-off position If your paper's perforation is not aligned with the tear-off edge, you can use the Micro Adjust function to move the perforation to the tear-off position, as described below. Your tear-off position setting remains in effect until you change it, even if you turn off the printer. c Caution: the knob to adjust the tear-off position; this may damage the Never use printer or cause it to lose the tear-off position. [. . . ] If this equipment has more than one interface connector, do not leave cables connected to unused interfaces. Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. For Canadian users This Class B digital apparatus meets all requirements of the Canadian Interface Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouileur du Canada. EPSON AMERICA, INC. , LIMITED WARRANTY What Is Covered: Epson America, Inc. ("EPSON") warrants to the first end user customer of the EPSON product enclosed with this limited warranty statement that the product, if purchased and used in the United States or Canada, conforms to the manufacturer's specifications and will be free from defects in workmanship and materials for a period of three years from the date of original purchase. [. . . ]