User manual FANTOM TWISTER FM760 INSTRUCTION MANUAL

[. . . ] Do not clean or store the vacuum cleaner in places where there are high temperatures. Before servicing the vacuum cleaner, allow all metal parts to cool first. Always place foot on handle release when adjusting the handle position of the vacuum cleaner. If the supply cord of this appliance is damaged, it must only be replaced by FANTOM , because special purpose tools are required. SAVE THESE INSTRUCTIONS This vacuum cleaner is intended for household use only. Note to user concerning attachment plug: To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). [. . . ] 2 Push the body compartment into on the main the main as shown to reattach. Projection Groove 9 CLEANING THE FILTERS 1 Remove the dust compartment. (refer to page 9) Set the dust compartment to the 2 position. Open the trapdoor, then parallel push the release button E and pull out the main filter. Allow items to Caution: Do not use a hard-bristled brush to clean filters. Do not attempt to dry with a hair dryer or by placing in a clothes dryer. Hot air may cause the filters to warp. Release Button E Cleaning Utensil To maintain optimum suction power, the dust filter fins should be kept clean of dirt. Clean the filter fins free of dirt with the forked end of cleaning utensil as shown. Cleaning Utensil Reattaching the filters 1 Insert the main filter into the prefilter as shown. Prefilter onto the main filter 2 Holddust compartment. and insert into the Align the ribs of the main filter to match the shape of the opening in the dust compartment and press firmly to insert. Dust Compartment Hole Main Filter Ribs 3 Close the trapdoor. 10 CLEARING BLOCKAGES IN THE SUCTION HOSE AND CLEANING THE AGITATOR ASSEMBLY Caution: Be sure to turn the ON/OFF switch to the "OFF" position and disconnect the power cord from the wall outlet before clearing any blockages in the suction hose and cleaning the agitator assembly. Clearing blockages in the suction hose Set the 1 Removevacuum cleaner to the upright position. 2 then remove hoseblockagesthe suction inlet and Pull inspection cover out the bypass tube assembly. 3 pushthe dust dust clogging theaway from body and cuff to inlet, and dust inspection cover to the bypass tube assembly. 4 Reattach theonhose vacuum the suctioncheck that the Now switch the cleaner to Hose Cuff Suction Inlet Dust Inspection Cover Bypass Tube Assembly the blockage has been properly cleared. If the hose is still blocked, the suction force will be weak. Clearing blockages in the nozzle head Remove the bottom plate (refer to page 14) Remove any blockages from the nozzle head. Reattach the bottom plate to the nozzle head, and then operate the vacuum cleaner to check that the blockage has been properly cleared. If the nozzle head is still blocked, the suction force will be weak. Nozzle Head Cleaning the blockage in the nozzle air inlet pipe If the nozzle head still appears to be blocked, please clear the blockage in the nozzle air inlet pipe. Reattach the vacuum cleaner. Release Button F Release Button F Nozzle air inlet pipe Nozzle air inlet pipe Caution: Make sure that the Release Button F is at the original position. Cleaning the agitator assembly When threads get caught in the agitator assembly, clean the assembly. Scissors Threads 11 REPLACEMENT INSTRUCTIONS Caution: Be sure to turn the ON/OFF switch to the"OFF" position and disconnect the power cord from the wall outlet before replacing any of the parts below. REPLACING THE HEADLIGHT LAMP 1 Set the vacuum cleaner to the parallel position. 2 Loosen the screws to remove the lens. 3 When removing the headlight lamp, be careful not to pull on the headlight lamp wiring. Lens Headlight Lamp Screw 4 Remove the lamp by pushing it gently in the direction of the arrow and then turning it counterclockwise. Lamp Socket 5 Push a new lamp gently into the socket and turn it clockwise to tighten it . Always replace the old filter with a new one. a new filter with the seal 3 Insert inside HEPAvacuum cleaner. Caution: Be sure that seal on the HEPA filter is inserted towards the inside of the vacuum cleaner. Do not reattach it upside down. Seal 15 TROUBLESHOOTING If there is a problem with the vacuum cleaner, carry out the following checks to find the cause. If the problem still persists after the checks have been made, do not use the vacuum cleaner to prevent the possibility of an accident occurring. Turn the ON/OFF switch to the "OFF" position, disconnect the power cord from the wall outlet, and contact FANTOM Customer Service at 1-800-275-9251. [. . . ] In no event is FANTOM liable for incidental or consequential damages of any nature whatsoever. Some states do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Be sure to include proof of purchase date and to attach tag to item before packing with your name, complete address and phone number with a note giving purchase information, model number and what you believe is the problem with item. [. . . ]