Detailed instructions for use are in the User's Guide.
[. . . ] Outdoor Gas Barbeque/Grill
Assembly manual and Use and Care
MODEL
FG50069
!WARNING!
Hazardous Fire or Explosion may result if these instructions are ignored.
It is your responsibility to see that your new barbeque is assembled, installed, maintained and cared for properly. Failing to carefully follow the instructi ns in this manual could o result in serious bodily injury and/or property damage. If odor continues, keep away from the appliance and immediately call your gas supplier or your fire department.
WARRANTY INFORMATION
Full Model No. [. . . ] 6. If the burner does not light immediately (within five seconds), turn burner control knob off and wait 5 minutes to clear the gas. If burner still fails to light, refer to Troubleshooting Guide to determine cause and solution, or try the Match Lighting procedure (Fig. 11A
LIGHTING THE OTHER MAIN BURNERS
Once one burner has been lit, push in and turn the adjacent control knob to `HIGH'. Place an ignited lighter or lit match through the lighting hole, approx. If it does not, extinguish the lighter or match, turn the control knob to off, and wait 5 minutes to clear the gas. If burner fails to light, refer to the Troubleshooting Guide to determine cause and solution. Once left hand burner is lit, light remaining burners in this sequence: center burner, then left burner.
BURNER
MATCH
MATCH LIGHTING HOLE
LIGHTING THE OTHER MAIN BURNERS
Once one burner has been lit, push in and turn the adjacent control knob to `HIGH'. If burner does not light immediately (within five seconds), turn the burner control knob off, and wait 5 minutes to clear the gas. If burner still fails to light, refer to the Troubleshooting Guide to determine cause and solution, or try the match lighting procedure below.
3. FAILURE TO DO SO MAY CAUSE SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE.
Fig. Place an ignited lighter or lit match near the ports, approximately 1/2" (1. 25 cm) from burner (see Figure 12B). If it does not, extinguish the lighter or match, turn the control knob off, and wait 5 minutes for the gas to clear. If burner still fails to light, refer to the Troubleshooting Guide to determine the cause and solution.
1/2"
Fig. 12B
NOTE: WHEN USING THE SIDE BURNER, THE MAXIMUM POT SIZE IS 9" WIDE.
SIDE BURNER COOKING POTS
1. Maximum weight to be used on side burner should not exceed 10lbs (4. 5 kg) ( See Figure 12 C )
NOTE: MAXIMUM WEIGHT FOR SIDE BURNER 10 lb (4. 5 kg)
MAX
Fig. If burner does not light immediately (within five seconds), turn the burner control knob off, and wait 5 minutes to clear the gas. If burner still fails to light, refer to the Troubleshooting Guide to determine cause and solution, or try the match lighting procedure below.
1.
Fig. Place an ignited lighter or lit match near the ports, approximately 1/2" (1. 25 cm) from burner (see Figure 12E). Push in and turn the rotisserie burner control knob to 'HIGH'. If it does not turn off the control knob, extinguish the lighter or match, and wait 5 minutes for gas to clear. If burner still fails to light, refer to the Troubleshooting Guide to determine the cause and solution.
NOTE: DO NOT USE THE MAIN BURNERS WHEN THE ROTISSERIE BURNER IS LIT.
If the heat output from the burner(s) seem abnormally low, it may be caused by the regulator flow-limiting device being activated by a leak in the gas system, or improper lighting procedures. If this is suspected, shut off the cylinder valve and all burner valves. [. . . ] · Insert side burner grill.
SP87-18 1/4 20 X . 5 (4) WING BOLT
(A)
(B)
(C)
SP87-18 1/4 20 X . 5 (4) SHELF LOCK WING BOLT
26
SIDE BURNER HOSE ASSEMBLY
· Position hose into end of side burner venturi tube until groves line up (A). · Attach side burner Ignitor wire to terminal on side burner bracket. Ensure you read and understand warning below before proceeding.
!
WARNING
CAUTION: NEVER LIGHT THE SIDE BURNER WHILE THE SIDE BURNER LID IS DOWN. FAILURE TO DO SO MAY CAUSE SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE.
Electrode
(A)
(B)
Grooves Ignitor Wire
FI G. 9
27
GREASE TRAP ASSEMBLY
· Assemble grease pan with brackets as shown using (4) 10-b x . 375 screw self tap screws. [. . . ]