User manual FIRST ALERT FA148C 3-00

[. . . ] 6HFXULW\6\VWHP )$ & ) $ & & 1 R ARMED READY R A B C D 1 OFF 4 MAX 7INSTANT 2 AWAY 5 TEST 8 CODE 0 3 STAY 6BYPASS 9 CHIME # IIIIII R * READY FA560 HEAT COOL BYPASS ACTIVE 8VHU*XLGH K4855V1 3/00 TABLE OF CONTENTS System Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Zones. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Panic Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Enter the 2-digit user number (03-16) for the user you are adding or changing. Enter the new 4-digit security code for that user. 3. (User's Code) Changing the Master Code Follow the procedure for changing a user's code, but enter user 02. Additionally, when changing the Master code, you must perform step 3 twice with the same user code entry so that the new Master code will be accepted by the system. - 30 - Security Codes (cont'd) To Delete a User 1. (Master Code) +8 Enter 4-digit Master code, then press the 8 key. Example: Press 2 0 5 9 then 8 2. (User Number) Enter user number. Enter the 2-digit user number (03-16) for the user whose code you are deleting. Wait (about 3 seconds) until the keypad beeps once before pressing any other key. ----------- - 31 - Testing the System (To be conducted weekly) Using the 5 TEST Key The TEST key puts your system into a TEST mode, which allows each protection point to be checked for proper operation. The keypad sounds a single beep every 30 seconds as a reminder that the system is in this TEST mode. NOTE: An alarm message will not be sent to your alarm monitoring company during the following tests. READY TO ARM Disarm the system and close all protected windows, doors, etc. The READY message should be displayed and the green READY indicator (if present on the keypad) should also be lit. 2. (Security Code) + 5 TEST Enter 4-digit security code, then press TEST key. Open each protected door and window in turn and listen for three beeps from the keypad. Identification of each faulted protection point should appear on the display. The display will clear when the door or window is closed. 4. - 32 - Testing the System (cont'd) Walk in front of any interior motion detectors (if used) and listen for three beeps. The keypad should display the identification of the detector when the detector is activated. Note that if you are using wireless motion detectors, there is a 3-minute delay between activations. To test all smoke detectors, follow the manufacturer's instructions. The keypad should display the identification of each detector when each is activated. If you experience a problem with any protection point (no confirming sounds, no display), CALL FOR SERVICE IMMEDIATELY. When you have checked (and closed, where necessary) all protection points, no zone identification numbers should be displayed on the keypad. When you complete testing, exit the TEST mode by continuing with step 5. [. . . ] NOTIFIES (Insert B = Burglary, F = Fire) Local Sounding Device Police Dept. TESTING: Quarterly Monthly Weekly Fire Dept. Other continued on other side - 53 - OWNER'S INSURANCE PREMIUM CREDIT REQUEST E. SMOKE DETECTOR LOCATIONS Furnace Room Basement Kitchen Living Room Bedrooms Dining Room Attic Hall F. BURGLARY DETECTING DEVICE LOCATIONS: Front Door 1st Floor Windows Basement Door All windows Rear Door Interior locations All Exterior Doors All Accessible Openings, Including Skylights, Air Conditioners and Vents G. [. . . ]