User manual FLYMO MICROLITE 28

[. . . ] FO T IN AN ce O RT e use P feren I M befor e re d utur Rea in for f ta & re IO M AT R N For all customer enquiries or for replacement parts, contact:- 01325 300303 www. flymo. com eop. customer. services@electrolux. co. uk ¤ 1 Carton Contents lock-off button switchbox start/stop lever cable clip upper handle plastic handle knob bolt nut (if applicable) washer electric cable with moulded on plug motor cover fixing pin lower handle hood instruction manual plastic cutters IMPORTANT !Please check the contents of the carton are correct BEFORE assembling your new Flymo product. IF ANY PARTS ARE MISSING CONTACT:Electrolux Outdoor Products Customer Service Department direct Telephone : 01325 300303 Fax : 01325 318193 Safety If not used properly this lawnmower can be dangerous!This lawnmower can cause serious injury to the operator and others, the warnings and safety instructions must be followed to ensure reasonable safety and efficiency in using this lawnmower. [. . . ] It is important that the outer sheath is clamped correctly into the 3-pin plug. If in doubt consult your local Service Repairer or qualified electrician before the machine is used. The normal plug fuse and household fuse only protect the electrical equipment and are not a safeguard against electrocution. If your product is hard wired i. e. non-detachable mains electric cable, a conversion kit and extension cable is available from all Electrolux Outdoor Products Approved Service Centres which can be found in your local Yellow Pages. Assembly Instructions A 1 1 B nut (if applicable) washer 2 2 handle knob bolt Lower Handle to Hood Assembly (A) · Ensure the motor cover is fitted correctly, as illustrated · Tilt and lock motor cover into forward position before assembly 1. Insert lower handles through the 2 holes in the motor cover and push down. Secure lower handles to hood by firmly pushing fixing pins through holes in motor cover, handle and hood. Fitting Upper Handles to Lower Handles (B) 1. Ensure the upper handle is located correctly with the lock-off button on the switchbox uppermost 2. Make sure the cable is not trapped between the handles. 4 Starting and Stopping To Start your Lawnmower 1. Form loop in mains cable and push the loop through the slot as illustrated in picture (C) To secure, position loop over the hook and pull the cable back through the slot as illustrated in picture (D). To prevent a ring being cut in your lawn, tilt your lawnmower slightly (E). The switchbox is provided with a lock-off button (F1) to prevent accidental starting. Press and hold the lock-off button (F) on the switchbox, then squeeze one of the Start/Stop levers towards the upper handle (G). Continue to squeeze the start/stop lever towards the upper handle and release the lock-off button. (H) When the lawnmower has reached full speed gently lower it onto the lawn. IMPORTANT Do not use the start/stop levers intermittently C D 3. To prevent a ring being cut in your lawn, tilt your lawnmower slightly (E). Start mowing the edge of the lawn nearest to the power point so that the cable is laid out on the lawn you have already cut. (J) Mow twice a week in the growing season, your lawn will suffer if more than one third of its length is cut at one time. Do not Overload your Lawnmower Mowing long thick grass may cause the motor speed to drop, you will hear a change in the motor sound. If the motor speed drops you may overload your lawnmower which may cause damage. When mowing in long thick grass, a first cut with the cutting height set higher will help reduce the load. See Adjusting the Cutting Height. J 2. 5 Adjusting the Cutting Height & Cutting System Maintenance HIGHEST - This symbol visible after fitting THERE ARE 2 CUTTING HEIGHTS Height of cut is adjusted by turning over the cutting head. [. . . ] Failures due to the following are not covered, therefore it is important that you read the instructions contained in this Operator's Manual and understand how to operate and maintain your machine: Failures not covered by guarantee * Replacing worn or damaged plastic cutters * Failures as a result of not reporting an initial fault. * Failures as a result of not using the product in accordance with the instructions and recommendations contained in this Operator's Manual. * The following items listed are considered as wearing parts and their life is dependent on regular maintenance and are, therefore not normally subject to a valid warranty claim: Plastic Cutters, Electric Mains cable. Electrolux Outdoor Products does not accept liability under the warranty for defects caused in whole or part, directly or indirectly by the fitting of replacement parts or additional parts that are not either manufactured or approved by Electrolux Outdoor Products, or by the machine having been modified in any way EC Declaration of Conformity I, the undersigned M. [. . . ]