User manual FLYMO MULTITRIM 250D

[. . . ] FO T IN AN O RT e use ence I M P befor refer ure ead r fut R n fo retai & IO M AT R N For all customer enquiries or for replacement parts, contact:- 01325 300303 www. flymo. com eop. customer. services@electrolux. co. uk ¤ 1 Carton Contents Height Adjust Nut (if applicable) Handle Knob Steady Handle NonHeight Adjust Bolt Nut (if applicable) Handle Knob Bolt Steady Handle Guard Guard Instruction Manual Electric Cable with moulded on plug Electric Cable with moulded on plug Scraper Tool (Multi-Trim 200 only) Instruction Manual IMPORTANT !Please check the contents of the carton are correct BEFORE assembling your new Flymo product. IF ANY PARTS ARE MISSING CONTACT:Electrolux Outdoor Products Customer Service Department direct Telephone : 01325 300303, Fax : 01325 318193 Safety Please note: This manual covers various products. Please read the user instructions carefully to fully identify, assemble and use the features that apply to your trimmer. [. . . ] Adjust length of the handle to the most comfortable operating position (fig H). Re-tighten the height adjust knob. Auto Line Feed System If you have a Multi Trim 200, it will be fitted with a wire guard as shown in figure J2. Please note: Depending on which model you have purchased, your trimmer may be fitted with one line or two lines. When initially switching on the trimmer, a small length of line is fed out. A `clattering' noise will be heard when the nylon line hits the line cutter. After approximately 5 seconds the line will be cut to the correct length and the noise will reduce as the motor reaches full speed. · Make sure the motor is up to full speed before trimming or edging. If the noise of the nylon line being cut cannot be heard, more line will need to be fed out. To feed more line, it is first necessary to to allow the motor to stop completely, then re-start, allowing the motor to reach full speed. If problems are experienced with the automatic line feed refer to Fault Finding Chart. J1 J2 Multi Trim 200 only line cutter wire guard line cutter 4 How to Trim and Edge WARNING: The use of eye protection is recommended. Do not lean over the trimmer whilst trimming or edging, objects may be thrown by the cutting line. Overloading can be avoided by making sure the motor speed does not drop unduly. Disconnect from the mains electricity supply before attempting any maintenance or adjustment. BEFORE USE: Make sure that the line is fed out (if 2 lines are fitted, make sure both are fed out). Line is fed out automatically every time the trimmer head stops rotating and returns to operating speed. To convert to edging mode, depress locking button and twist head anti-clockwise until arrow lines up with "EDGE". (If 2 lines are fitted do this to one line only, then gently pull on the second line, there is no need to press the manual line feed button again). If the line extends past the line cutter, too much line has been fed out. If too much line is fed out, remove the spool cap and click spool anti-clockwise until the line is at the desired length. Please note: Depending on which model you have purchased, your trimmer may be fitted with one line or two lines. manual line feed button manual line feed button Spool Cap and Nylon Line (1 Line) T1 cap release latches To remove spool cap 1. Failure to do so may prevent the cap being securely located in the spoolholder. Align the two latches on the cap with the two windows in the spoolholder, then press down into the locked position. [. . . ] * The following items listed are considered as wearing parts and their life is dependent on regular maintenance and are, therefore not normally subject to a valid warranty claim: Nylon Line, Electric Mains Cable * Caution!Electrolux Outdoor Products does not accept liability under the warranty for defects caused in whole or part, directly or indirectly by the fitting of replacement parts or additional parts that are not either manufactured or approved by Electrolux Outdoor Products, or by the machine having been modified in any way. EC Declaration of Conformity I, the undersigned M. Bowden of Electrolux Outdoor Products, Aycliffe Industrial Park, NEWTON AYCLIFFE, Co. Electrolux Outdoor Products Conforms to the specifications of Directive 2000/14/EEC I, the undersigned M. [. . . ]