User manual FLYMO REVOLUTION 2000

[. . . ] T RIM M ODE T URN OVER TO E DGE E DGE M ODE FO T IN AN nce O RT e use M P efor efere I re r ead b for futu R tain & re IO M AT R N 1 Carton Contents Lock off Button Steady Handle Switch Lever Upper Shaft Electric Cable with moulded on plug Lower Shaft Safety Guard Instruction Manual IMPORTANT !Please check the contents of the carton are correct BEFORE assembling your new Flymo product. IF ANY PARTS ARE MISSING CONTACT:Electrolux Outdoor Products Customer Service Department direct Telephone : 01325 300303 Fax : 01325 318193 Safety If not used properly this trimmer can be dangerous!This trimmer can cause serious injury to the operator and others, the warnings and safety instructions must be followed to ensure reasonable safety and efficiency in using this trimmer. [. . . ] To secure, position loop over the hook and pull the cable back through the slot as illustrated in picture (E). 4 Double Auto Feed System How the automatic line feed works (F) 1. When initially switching on the trimmer, a small length of line is fed out. A `clattering' noise will be heard when the two nylon lines hit the line cutter. After approximately 5 seconds the line will be cut to the correct length and the noise will reduce as the motor reaches full speed. · Make sure the motor is up to full speed before trimming or edging. If the noise of the nylon line being cut cannot be heard, more line will need to be fed out. To feed more line, it is first necessary to to allow the motor to stop completely, then re-start, allowing the motor to reach full speed. If problems are experienced with the automatic line feed refer to Fault Finding Chart. F line cutter How to trim and edge · WARNING · The use of eye protection is recommended. Do not lean over the trimmer whilst trimming or edging, objects may be thrown by the cutting line. Overloading can be avoided by making sure the motor speed does not drop unduly. Disconnect from the mains electricity supply before attempting any maintenance or adjustment. · Make sure motor is up to full speed before trimming or edging. How to trim · The switchbox is provided with a lock-off button (G1) to prevent accidental starting. To start, press the lock-off button down (G1), whilst pressing the lock-off button squeeze the switch lever (G2). Line is fed out automatically every time the trimmer head stops rotating and returns to operating speed. To start, press the lock-off button down (K1), whilst pressing the lock-off button squeeze the switch lever (K2) 3. Rest edger on roller for extra stability and line up with the edge of the lawn, see fig M. Edge in direction indicated in fig L so that debris is thrown away from you. · Ensure the electric cable is not snagged or pulled around sharp objects. G 1 H 2 J K 2 1 L M 5 Fault Finding Chart WARNING Disconnect from the mains electricity supply before attempting any maintenance or adjustment. FAULT CHECK Is the automatic line feed working?Is the line fed out and visible? ACTION LINE NOT FEEDING OR LINE TOO SHORT OR TRIMMER VIBRATES No No No No Yes Yes ?SEE "MANUAL LINE FEED" Remove cap and spool, free line and re-fit spool and cap. SEE "SPOOL CAP AND NYLON LINE" The line may be jammed on the spool. [. . . ] Failures due to the following are not covered, therefore it is important that you read the instructions contained in this Operator's Manual and understand how to operate and maintain your machine: Failures not covered by guarantee * Replacing Nylon Line. * Failures as a result of not using the product in accordance with the instructions and recommendations contained in this Operator's Manual. * The following items listed are considered as wearing parts and their life is dependent on regular maintenance and are, therefore not normally subject to a valid warranty claim: Nylon Line, Electric Mains Cable * Caution!Electrolux Outdoor Products does not accept liability under the warranty for defects caused in whole or part, directly or indirectly by the fitting of replacement parts or additional parts that are not either manufactured or approved by Electrolux Outdoor Products, or by the machine having been modified in any way. EC Declaration of Conformity I, the undersigned M. [. . . ]