User manual FLYMO TURBOLITE 400

[. . . ] FO T IN TA N ce P O R ore use feren M I e re ef ad b for futur Re tain & re IO M AT R N For all customer enquiries or for replacement parts, contact:- 01325 300303 www. flymo. com eop. customer. services@electrolux. co. uk ¤ 1 Carton Contents IMPORTANT !Please check the contents of the carton are correct BEFORE assembling your new Flymo product. IF ANY PARTS ARE MISSING CONTACT:Electrolux Outdoor Products Customer Service Department direct Telephone : 01325 300303, Fax : 01325 318193 cable clip x 2 upper handle bolt nut x 2 (if applicable) washer x 2 plastic handle knob x 2 electric cable with moulded on plug fixing pin instruction manual lower handle spanner/scraper tool cutting height spacers (Turbo Lite 330 - 1 fitted to lawnmower & 2 in loose parts pack) (Turbo Lite 350/400 - 1 fitted to lawnmower & 3 in loose parts pack) Safety If not used properly this lawnmower can be dangerous!This lawnmower can cause serious injury to the operator and others, the warnings and safety instructions must be followed to ensure reasonable safety and efficiency in using this lawnmower. [. . . ] If in doubt consult your local Service Repairer or qualified electrician before the machine is used. The normal plug fuse and household fuse only protect the electrical equipment and are not a safeguard against electrocution. non-detachable mains electric cable, a conversion kit and extension cable is available from all Electrolux Outdoor Products Approved Service Centres which can be found in your local Yellow Pages. 3 Assembly A lower handle slots Fitting the Lower Handles to Your Lawnmower (A) 1. Secure lower handles to hood by firmly pushing fixing pin through holes in hood and handle. NOTE Should a problem occur when securing handle to hood with the fixing pin, carefully lever fixing pin out of location and repeat steps 1 to 3 above. fixing pin B Fitting Upper Handles to Lower Handles (B) lock-off button nut 1. Ensure the upper handle is located correctly with the lock-off button on the switchbox uppermost. Ensure the upper handle and the lower handle are aligned correctly. 3. 4. Make sure the cable is not trapped between the upper and lower handles. Handle Adjustment C · WARNING!STOP THE LAWNMOWER AND WAIT UNTIL THE BLADE HAS STOPPED ROTATING BEFORE ADJUSTING THE HANDLE. REMOVAL OF LOWER HANDLE FIXING PINS IS NOT REQUIRED TO ADJUST THE HANDLE ADJUST THE HANDLE (C) Hold handle as illustrated. 5. HANDLE IN FORWARD POSITION Follow procedure described in "TO ADJUST THE HANDLE" and push handle forward until it stops. HANDLE IN DOWN POSITION Follow procedure described in "TO ADJUST THE HANDLE" and move handle downward until it stops. . HANDLE IN OPERATING POSITION Adjustment is not required to move the handle to the operating position Simply pull down from the forward position or lift up from the down position until the handle is in the most comfortable operating position. PULL LOWER HANDLE 4 Starting and Stopping To Start your Lawnmower 1. Connect female extension cable connector to the back of the switchbox. Form loop in mains cable and push the loop through the slot as illustrated in picture (E) 3. To secure, position loop over the hook and pull the cable back through the slot as illustrated in picture (F). To prevent a ring being cut in your lawn, tilt your lawnmower slightly (G). The switchbox is provided with a lock-off button (H1) to prevent accidental starting. Press and hold the lock-off button (H1) on the switchbox, then squeeze one of the Start/Stop levers towards the upper handle (J). Continue to squeeze the start/stop lever towards the upper handle and release the lock-off button. When the lawnmower has reached full speed gently lower it onto the lawn. · IMPORTANT Do not use the start/stop levers intermittently To Stop your Lawnmower 1. [. . . ] Electrolux Outdoor Products does not accept liability under the warranty for defects caused in whole or part, directly or indirectly by the fitting of replacement parts or additional parts that are not either manufactured or approved by Electrolux Outdoor Products, or by the machine having been modified in any way Environmental Information Electrolux Outdoor Products are manufactured under an Environmental Management System (ISO 14001) using, where practical, components manufactured in the most environmentally responsible manner, according to company procedures, and with the potential for recycling at the end of the products' life. · Packaging is recyclable and plastic components have been labelled (where practical) for categorised recycling. · Awareness of the environment must be considered when disposing of `end-of-life' product. · If necessary, contact your local authority for disposal information. EC Declaration of Conformity I, the undersigned M. [. . . ]