Detailed instructions for use are in the User's Guide.
[. . . ] 12FG
12 CHANNEL RADIO CONTROL SYSTEM PCMG3/PCM1024/FM selectable
INSTRUCTION MANUAL
Note: The battery in the T12FG transmitter is not connected to the battery connector at initial. Please connect the battery connector before use.
1M23N18902
TABLE OF CONTENTS
INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 reading) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Trainer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Fuselage linkage Connect the throttle rudder, aileron, elevator, pitch, and other servos in accordance with the kit instruction manual. For a description of the connection method, see "Receiver and Servos Connection".
Note: The channel assignment of the T12FG is different from that of our existing systems. (The channel assigned to each function can be checked at the Function menu of the Linkage Menu. )
5. Throttle/Pitch curve setting This function adjusts the throttle or pitch operation curve in relation to the movement of the throttle stick for each condition.
Call the throttle curve of each condition with the condition select switch.
< Call the pitch curve of each condition with the condition select switch.
º~6º
*Stability at hovering may be connected to the throttle curve. Adjustment is easy by using the hovering throttle function and hovering pitch function together.
º
º
º
º *If any interactions are noticed, for a description of the linkage correction function, please refer to the SWASH function, p. 65.
º
<Model Basic Setting Procedure>
39
6. AFR (D/R) AFR (D/R) function is used to adjust the throw and operation curve of aileron, elevator and rudder for each condition.
*For throttle and pitch curve settings, refer to the abovementioned "Throttle/Pitch curve setting"
Model Menu, and set the curve for each condition.
maximum throw directions. Call the mixing curve of each condition with the condition select switch.
*For this curve, use the initial setting [EXP1] curve type. Gyro sensitivity and mode switching The gyro sensitivity and mode switching function is dedicated gyro mixing of the Model Menu, and can be set for each condition.
*For this curve, [EXP1] curve type can be used and the entire curve can be lowered with the [Offset] function.
º *For this curve, [EXP1] curve type can be used and the entire curve can be lowered with the [Offset] function.
9. Throttle hold setting
*If throttle hold is necessary, please refer to the THR HOLD function, p. 113.
10. Throttle cut setting
Note: When using a GY601, GY502, GY401, or other heading hold gyro, this Pitch to RUD mixing should not be used. When operating the gyro in the AVCS mode, the mixed signal will cause neutral deviation symptoms and the gyro will not operate normally.
Throttle cut provides an easy way to stop the at idle. The action is not functional at high throttle to avoid accidental dead sticks. The switch's location and direction must be chosen, as it defaults
Use this function when you want to suppress the torque generated by the changes in the pitch and speed of the main rotor during pitch operation. However, when using a heading hold gyro like those shown below, do not use Pitch to RUD mixing. Call the Pitch to RUD mixing function from the
*With throttle stick at idle, adjust the cut position until the engine consistently shuts off, but throttle linkage is not binding.
40 <Model Basic Setting Procedure>
pitch interaction The swash mix function is used to correct the swash plate in the aileron (Left/Right Cyclic) and elevator (Forward/Aft Cyclic) direction corresponding to each operation of each condition.
*If throttle mixing is necessary for a compensation for slowing of engine speed caused by swash plate operation during aileron or elevator operation, please refer to the THROTTLE MIX function, p. 113.
<Model Basic Setting Procedure>
41
Receiver and servo connection
Connect the receiver and servos in accordance with the connection diagram shown below. Always read [Precautions when mounting the receiver and servos] or [Before using]. When mounting the receiver and servos to the fuselage, connect the necessary points in accordance with the kit instruction manual. Receiver and servos connection diagram
~ ~
Ni-Cd battery
Charging port/ DSC connector
Receiver switch
Servos
The Servo connection by model type tables are shown on the following pages. Connect the servos to match the fuselage used.
42 <Model Basic Setting Procedure>
Servo connection by model type
The T12FG transmitter channels are automatically assigned for optimal combination according to the type selected with the Model Type function of the Linkage Menu. The channel assignment (initial setting) for each model type is shown below. Connect the receiver and servos to match the type used.
*The set channels can be checked at the Function screen of the Linkage Menu. For more information, read the description of the Function menu.
Airplane/glider/motor glider
[PCM-G3 mode]
RX CH 1AIL 2AIL 2AIL+1FLAP 2AIL+2FLAP 2AIL+4FLAP 4AIL+2FLAP 4AIL+4FLAP
Airplane Glider Airplane Glider Airplane Glider Airplane Glider Airplane Glider Airplane Glider Airplane Glider
6
9
[PCM1024/PPM mode]
RX CH 1AIL 2AIL 2AIL+1FLAP 2AIL+2FLAP 2AIL+4FLAP 4AIL+2FLAP
Airplane Glider Airplane Glider Airplane Glider Airplane Glider Airplane Glider Airplane Glider
6
<Model Basic Setting Procedure>
43
[PCM-G3 mode]
RX CH 1AIL 2AIL 2AIL+1FLAP 2AIL+2FLAP 2AIL+4FLAP 4AIL+2FLAP 4AIL+4FLAP
Airplane Glider Airplane Glider Airplane Glider Airplane Glider Airplane Glider Airplane Glider Airplane Glider
6
9
[PCM1024/PPM mode]
RX CH 1AIL 2AIL 2AIL+1FLAP 2AIL+2FLAP
Airplane Glider Airplane Glider Airplane Glider Airplane Glider
6
44 <Model Basic Setting Procedure>
[PCM-G3 mode]
RX CH 2AIL 2AIL+1FLAP 2AIL+2FLAP 2AIL+4FLAP 4AIL+2FLAP 4AIL+4FLAP
Airplane Glider Airplane Glider Airplane Glider Airplane Glider Airplane Glider Airplane Glider
6
9
[PCM1024/PPM mode]
RX CH 2AIL 2AIL+1FLAP 2AIL+2FLAP 2AIL+4FLAP 4AIL+2FLAP
Glider Glider Glider Glider Airplane Glider Airplane Glider Airplane Glider Airplane Airplane Normal Winglet Normal Winglet
6
<Model Basic Setting Procedure>
45
Helicopter [PCM-G3 mode]
RX CH
1 2 3 4 5 6 7 8 9 10 11 12 VC1 VC2 VC3 VC4
H-4, H4X Swash
Throttle Rudder Aileron Elevator Pitch Elevator 2 Gyro Governor 1 Governor 2 Needle AUX2 AUX1 AUX1 AUX1 AUX1 AUX1
All Other
Throttle Rudder Gyro Aileron Elevator Pitch Governor 1 Governor 2 Needle AUX3 AUX2 AUX1 AUX1 AUX1 AUX1 AUX1
[PCM1024/PPM mode]
RX CH
1 2 3 4 5 6 7 8 VC1 VC2 VC3 VC4
H-4, H4X Swash
Throttle Rudder Aileron Elevator Pitch Elevator 2 Gyro Governor 1 AUX1 AUX1 AUX1 AUX1
All Other
Throttle Rudder Gyro Aileron Elevator Pitch Governor 1 Governor 2 AUX1 AUX1 AUX1 AUX1
46 <Model Basic Setting Procedure>
FUNCTIONS OF LINKAGE MENU
The Linkage Menu is made up of functions which perform model addition, model type selection, frequency setting, end point setting, and other model basic settings. [. . . ] To return to the preceeding screen, move the cursor to the [HARDWARE SEL. ] at the top of the screen and push the EDIT button. Or, move the cursor to the [ON/OFF] and call the ON/OFF position setting screen by pushing the EDIT button.
When switch was selected When switch was selected, ON/OFF position setting is also performed.
1. When you want to change the mode, move the cursor to [MODE] and push the EDIT button to switch to the data input mode. Switch the display to the mode you want to change by turning the EDIT dial to the left or right and then make the change by pushing the EDIT button. [. . . ]