User manual FUTABA 3PJ

[. . . ] Prior to operating your 3PJ SUPER, please read this manual thoroughly and use your system in a safe manner. After reading this manual store it in a safe place. See the glossary on page (P108-109) for the definition's of the special terms used in this manual. Application, Export and Reconstruction 1. The product described in this manual is subject to regulations of the Ministry of Radio/Telecommunications and is restricted under Japanese law to such purposes. Exportation Precautions (a) When this product is exported from Japan, its use is to be approved by the Radio Law of the country of the destination. [. . . ] 30% (If this value is too high, the braking distance will increase. ) CYCL: 5~7 DUTY: 0 (When grip is low: - side, when grip is high: + side) DLY: 10~15% TG. P: Approx. 70% STM: OFF - When the wheels lock, or the car spins, when the brakes are applied fully AB. P: Increase from 30% DUTY: Shift from 0 to - side (-1, -2, -3) DLY: Reduce the delay - When the braking effect is poor and the braking distance is long when the brakes are applied fully AB. P: Decrease from 30% DUTY: Shift from 0 to + side (+1, +2, +3) DLY: Increase the delay 54 Select Mode Functions Idle-Up Use this function to improve the starting characteristics of the engine by raising the idling speed when starting the engine of a gas powered car. Operation Offsets the throttle neutral position to the forward side or brakeside. 1. Call the idle-up function setup screen by pressing the UP key four times at the initial screen. Adjust the idle-up rate with the + or - key. Blink DIRECT SELECT TH. EXP ST. EXP UP SETUP DOWN ATV M. SEL RESET CUSTOM + - - 4 times Setting range: D50~0~U50% "U": Forward side, "D": Brake side - Return to the initial value (0%) by pressing the + and - keys simultaneously for about one second. DIRECT SELECT TH. EXP ST. EXP UP SETUP DOWN ATV M. SEL RESET CUSTOM + - 3. (The display returns to the initial screen. ) DIRECT SELECT TH. EXP ST. EXP UP SETUP DOWN ATV M. SEL RESET CUSTOM + - - 4 times Switch Setting Select the idle-up function ON/OFF switch with the function select switch function. If the power switch is turned on while the idle-up switch is on, an audible alarm will be heard. Immediately set the Idle-Up switch to OFF. Select Mode Functions Setting Amount The standard value (100% point) of this setting is unrelated to the travel set by the throttle ATV function. It is 50% of the forward side and brake side total servo throw from the servo neutral position. 55 Throttle Acceleration Gas powered cars require a slight clearance in the linkage. The response of an electric car is obtained by reducing this time lag at the transmitter. Carburetor A slight clearance is required at the linkage, but the throttle acceleration function acts to reduce the time lag caused by this clearance. Servo horn Brake side Operation - Sharply increases the throttle response near the throttle triggerneutralposition. - The forward side and brake side can be adjusted independently. 1. (Forward side setting) Call the throttle acceleration function set-up screen by pressing the UP key five times at the initial screen. Adjust the forward side with the + or - key. DIRECT SELECT TH. EXP ST. EXP UP SETUP DOWN ATV M. SEL RESET CUSTOM Blink + - - 5 times Setting range: 0~100% - Return to the initial value (0%) by pressing the + and - keys simultaneously for about one second. DIRECT SELECT TH. EXP ST. EXP UP SETUP DOWN ATV M. SEL RESET CUSTOM + - 56 Select Mode Functions 3. (Back side setting) Call the back side set-up screen by pressing the SELECT key once. Adjust the back side with the + or - key. DIRECT SELECT TH. EXP ST. EXP UP SETUP DOWN ATV M. SEL RESET CUSTOM Blink + - DIRECT SELECT TH. EXP ST. EXP UP SETUP DOWN ATV M. SEL RESET CUSTOM + - Setting range: 0~100% - Return to the initial value (0%) by pressing the + and - keys simultaneously for about one second. 5. (The display returns to the initial screen. ) DIRECT SELECT TH. EXP ST. EXP UP SETUP DOWN ATV M. SEL RESET CUSTOM + - -5 times Setting Amount The standard value (100% point) of this setting has an affect on the travel set by the throttle ATV function. Select Mode Functions 57 Start Function When the throttle trigger is set to full throttle simultaneously with starting when the track is slippery, the car wheels will spin and the car will not accelerate smoothly. When the Start function is activated, merely operating the throttle trigger slowly causes the throttle servo to automatically switch from the set trigger position to a preset point so that the tires do no loose their grip and the car accelerates smoothly. Without Start function Wheels spin - Car does not accelerate With Start function Tires grip the track firmly - Car accelerates Start Function Operation - When the throttle stick is moved to the preset position (throttle position: TG. P), the throttle servo moves to the preset position. - When the throttle stick is operated slowly so that the wheels will not spin, the car automaticallyacceleratestothesetspeed. - This function is effective only for the first throttle trigger operation at starting. - When the throttle trigger is returned slightly, the Start function is automatically deactivated and the set returns to normal throttle trigger operation. Operation by Switch When the switch is pressed, the throttle servo will move to the preset position without regard to the throttle trigger position. [. . . ] 1 will be forcibly called. 105 Reference Audible alarm: Tone will sound (9 times), then repeat. LCD screen: Audible alarm: Tone sounds (7 times) and stops (repeated) Blink Data Pac Error If data transfer with the Data Pac was not performed normally, an audible alarm will sound and "CAMERR" will be displayed on the LCD screen. - To stop the alarm, press the + and - keys simultaneously for about one second. If the alarm is not generated, there is no problem. LCD screen: Audible alarm: Tone sounds (7 times) and stops (repeated) Blink Memory Error If the data in the transmitter is not transferred normally when the power is turned on, an audible alarm will sound and "MEMERR" will be displayed on the LCD. - To stop the alarm, press the + and - keys simultaneously for about one second. If the alarm is not generated again, there is no problem. LCD screen: Audible alarm: Tone sounds (7 times) and stops (repeated) Blink Idle-Up Warning When the power switch is turned on while the idle-up function switch is on, an audible alarm will sound. Audible alarm: Tone sounds (7 times) and stops (repeated) 106 Reference Glossary The following defines the symbols and terms used in this instruction manual Band Frequency that receiver and transmitter operate on. Throttle Devise that controls the air mixture at the engine intake. [. . . ]