User manual FUTABA FP-2NBL

[. . . ] When the voltage of the running Nicd battery recovers, ASP is automatically reset and the normal running functions are recovered by turning on the transmitter power switch. (Installed in NEW ATTACK-BPR) World's first safety system that allows running of the vehicle up to the finish line while using the capacity of the power supply to the fullest without a loss of steering control even when the voltage of the running Nicd battery drops. ·Transmitter is Built-in servo reverse switches. (New ATTACK-R, NEW ATTACK-BFR) TRANSMITTER FP-T2NBL/T2NBR/T2NBFR ·ASP (Adjustable Safety Position) system allows safe recovery without a loss of steering control. (T2NBFR only) ·New swivel stick system that allows selection of the stick lever operating direction over a range of 10°. [. . . ] ·Adjust the trim lever so that the vehicle runs straight on a smooth road. The throttle trim lever is used to fine adjust the speed controller stop position, etc. 3 ·THROTTLE STICK NEUTRAL LEVER OPERATION ·The neutral position of the throttle stick (engine control stick) at the left side can be selected in two stages by moving the neutral lever as shown in the figure. When neutral lever up When neutral lever down If the neutral lever is moved, the neutral position of the stick lever can be adjusted in two steps as shown in the figure. When the neutral lever is up, the throttle stick can be adjusted to a total of 54°, 27" up and 27° down, from the neutral position. This position is best for electric cars and other models with which the center of the speed controller is the neutral position. When the neutral lever is down, the throttle stick can be adjusted to a total of 54°, 36° up and 18° down (2-to-1), from the neutral position. This position is best for engine-drive cars or other models with which the speed controller neutral position is offset. ·CHANGING THE THROTTLE STICK FROM A SELF NEUTRAL SYSTEM TO A RATCHET SYSTEM ·When changing the throttle stick from a self-neutral system to a ratchet system, install the optional slider. Then, remove the spring and swing arm. ·Futaba Digital Proportional Frequencies (FOR U. S. A. ) · The frequency of Futaba digital proportional sets can be changed among bands (1) ~ (6) on the 27MHz band only. · However, a 27MHz band set cannot be changed to 72MHz band, and vice versa. · Therefore, always, attach the correct frequency flag to the end of the transmitter antenna. Always use a Futaba crystal set (transmitter, receiver) when changing the frequency. · It is illegal to change crystals of transmitter on the 72-75 MHz bands in the U. S. A. Twist with long-nose pliers. Remove the spring and swing arm. ·CRYSTAL REPLACEMENT ·When changing the band, remove the crystal holder and change the crystal. 75MHZ) ·SWIVEL STICK SETTING · To adjust the operating direction of the stick lever, loosen the four screws shown in the figure and turn the stick body and set it to the best position. After setting the stick, retighten the four screws. (1) Loosen these four screws. (3) Tighten these four screws. Stick lever can be set within this range. 5° 4 (2) Select the angle by turning the stick body. mark is displayed on the front of the receiver of BEC The system sets with a receiver with shared power supply regulator. RECEIVER FP-R102GF AND SERVO FP-S128 Receiver crystal Steering servo Receiver FP-R102GF ON OFF Throttle servo Antenna wire Switch Connection to this connector (1) When chassis power supply of engine or motor car is separate Red common 2P Wrapped with connector rubber bands. Red common 2P connector (male pins) Connect the servo and switch as shown in the figure and extend the transmitter and receiver antenna fully. (Female pins) (75MHz-OPTIONAL) (3) When motor car uses an ordinary common power supply chassis (2) When motor car uses a special BEC system chassis (common power supply specifications) Red common 2P connector Red common 2P connector Controller (Female pins) Buy the red common 2P connector from the kit manufacturer and connect to the controller. The range of the radiowaves will be shortened. Wood screw Receiver antenna wire Rubber bushing Grommet R102GF Scissors Install the servos firmly. In other cases, install the servo as described in the model manufacturer's manual. ·Wrap the receiver in sponge rubber and wrap rubber bands around the sponge rubber. Mount the receiver so it is not exposed to vibration, does not touch the frame, and does not move. ·When the receiver is installed on a board or used where it may be splashed with mud and water, place it in a plastic bag, etc. and wrap a rubber band around the open end of the bag to waterproof and dustproof the receiver. · Use the rubber bands wrapped around the receiver to hold the servo and switch leads. ·After mounting is complete, recheck each part, then check the transmitting range by making the transmitter antenna as short as possible and extending the receiver antenna fully and operating the set from a distance of 20m to 30m. The movement of each servo should follow the movement of the transmitter sticks. [. . . ] This will facilitate detection of the trouble point and shorten the repair period greatly. ·Defects caused by faulty materials or workmanship will be corrected free of charge. ·This limited warranty is null and void if the set has been tampered with or disassembled. Refer to warranty statement for details. WORLD SALES & SERVICE FACILITIES Australia: Argentine: Canada: Chile: Denmark: England: Finland: Greece: Hong Kong: Italy: FUTABA SALES AUSTRALIA PTY. [. . . ]