User manual FUTABA FP-2PB
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual FUTABA FP-2PB. We hope that this FUTABA FP-2PB user guide will be useful to you.
Manual abstract: user guide FUTABA FP-2PB
Detailed instructions for use are in the User's Guide.
[. . . ] (Output torque 42 oz-in <3kg, cm), operating speed 0. 22 sec/60°). · New indirect drive/completely sealed potentiometer substantially improves vibration and shock resistance, and neutral accuracy. ·Unique Futaba power-saving custom 1C provides high starting torque narrow dead band, and excellent trackability. ·Fiberglass P8T (polybutylene terephthalate) servo case is mechanically strong and is invulnerable to glow fuel. [. . . ] ·Special pad grommets simplify mounting of the servo, and are extremely vibration-resistant. ·High 42 oz-in (3kg-cm) output torque is perfect for almost all models.
RECEIVER FP-R102JE
·Miniature and lightweight high-performance AM 2CH receiver with built-in BEC is realized by using chip parts. (20% smaller and 35% lighter than our R102GF. ) · Intermodulation interference characteristic improved substantially by using a new circuit system AIC circuit. ·Reliability is improved further by using the unique Futaba custom decoder 1C. ·High-performance built-in BEC system can handle power supply voltages up to 8. 4 V.
Transmitter Receiver Servo Others
FP-2NCR FP-2PB FP-T2NCS x 1 FP-T2NCR x 1 FP-R102JE x 1 FP-R102JE x 1 FP-S148x 2 FP-S148 x 2 Switch, frequency flag, etc.
Specifications are subject to change without prior notice.
Transmitter FP. T2NCS/T2NCR Operating system Transmitting frequency Modulation Power requirement Current drain 2 stick 27MHz bands 1 to 6. 72, 75MHz AM (Amplitude Modulation) 12 0V. penlight battery x 8 170mA Receiving frequency Intermediate frequency Power requirement Current drain Dimensions Weight Range
Receiver-- FP-R102JE 27 MHz and 72/75 MHz band 455 kHz 4. 8 V to 8. 4 V (BEC built-in) 8. 4V/12mA, 4. 8V/33mA (no signal) 1. 23x 1. 87 x 0. 78 in 133x47. 4 x 19. 8mm) 0. 88 oz 125 g) 300 m on the ground with FP-T2NCS T2NCR (At the best radio wave condition of environment) 1 Control system Operating angle Powar requirement Current drain (IDLE) Output torques Operating sp--ed Dimensions Weight
SERVO FP-S148
+pulse width control One side 45° or more 4. 8V-6V 6. 0V, 8mA (at idle) 42 oz. (40. 4 x 19. 8 x 36 mm) 1. 5 oz. (44. 4g)
· Nomenclature ·The name of each part of the transmitter is shown in the figure. When running the vehicle, extend the antenna fully.
Before using the set, check the remaining battery capacity by checking the level meter.
Good
Caution
No good
Change the battery.
Frequency flag
Antenna
Level meter
Throttle trim
Throttle stick Steering stick Steering trim
Power switch Servo reverse switches (FP-2NCR)
·USING THE FREQUENCY FLAG
First digit
Second digit The flag can be attached to and removed from, the antenna with one touch.
Attach the frequency flag to the flag holder as shown in the figure. 2
·LOADING THE PENLIGHT BATTERIES
· Remove the battery cover at the rear and insert eight penlight batteries in the correct polarity. Rear cover mounting screws
Servo reverse switches (FP-T2NCR) Slide in the direction of the arrow while pushing here.
The batteries can be easily loaded by inserting them four at a time from the back.
· Extend the antenna fully and set the power switch to ON. If the pointer does not move, or moves very little, check for poor battery contact, incorrect battery polarity, or faulty batteries. If metal parts touch each other due to vibration, noise will be generated and cause the receiver servos to operate erroneously. · Even though the receiver antenna wire is long, do not cut or bundle it. - Wood screw Receiver antenna wire Rubber bushing Grommet · Install the servos firmly. In other cases, install the servo as described in the model manufacturer's manual.
R102JE
Scissors
· A spare horn is provided. ·Wrap the receiver in sponge rubber and wrap rubber bands around the sponge rubber. Mount the receiver so it is not exposed to vibration, does not touch the frame, and does not move. ·When the receiver is installed on a board or used where it may be splashed with mud and water, place it in a plastic bag, etc. and wrap a rubber band around the open end of the bag to waterproof and dustproof the receiver. · Use the rubber bands wrapped around the receiver to hold the servo and switch leads. ·After mounting is complete, recheck each part, then check the transmitting range by making the transmitter antenna as short as possible and extending the receiver antenna fully and operating the set from a distance of 20m to 30m. The movement of each servo should follow the movement of the transmitter sticks. [. . . ] (Except 72/75MHz in U. S. A) Always use a Futaba transmitter and receiver crystal pair as the replacement crystals.
6
Your NEW FUTABA Digital Proportional R/C Systern is guaranteed against defects in workmanship and material for 180 days from the date of purchase when the attached registration card is returned to us within ten days of purchase. This Guarantee is null and void if the R/C system has been improperly handled, damaged in a crash, or tampered with and does not cover the replacement of plastic housings or electronic components damaged due to the use of improper voltages. When service is required, please take your equipment to your local authorized service station or ship it directly to us. All postage, shipping, and insurance charges must be paid by the user.
·When requesting repair of trouble that has occurred suddenly of from long use, describe the trouble symptoms in as much detail as possible. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE FUTABA FP-2PB
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual FUTABA FP-2PB will begin.