User manual FUTABA FP-6DN
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual FUTABA FP-6DN. We hope that this FUTABA FP-6DN user guide will be useful to you.
Manual abstract: user guide FUTABA FP-6DN
Detailed instructions for use are in the User's Guide.
[. . . ] Frequency changes are easily accomplished, because of the plug-in socket for the crystals. Throttle control Lever location can be easily changed from left to right side. Neck strap and Hook is provided for convenient handling.
RECEIVER
1. Because of the New 8-BIT integrated circuit device, used in all Futaba Receivers, all Futaba Propo. [. . . ] (Available Futaba pair crystal Tx/Rx) 27 MHz Areas 26. 995 (Brown) 27. 045 (Red) 27. 095 (Orange) 27. 145 (Yellow) 27. 195 (Green) 72 MHz Areas. * 72. 080 (Brown/White) 72. 160 (Blue/White) * 72. 240 (Red/White) 72. 320 (Violet/White) * 72. 400 (Orange/White) 72. 960 (Yellow/White) (**) * 75. 640 (Green/White) (**)
Remarks:
Mark * = Model Aircraft use only. The FP-R6D receiver incorporates an 8 Bit integrated circuit and is made into 6-channel operation. The same integrated circuit is also used for Four (4) and Five (5) channel operation. The Block connector sockets that connects the different Servos are an integral part of the receiver. The Block Connector sockets are polarized and each position is designated on the receiver case. Particularly care must be taken since the power supply relay connector is Red and the Aileron relay connector is BLACK. Since each Servo is built to the same specifications, any Servo can be used for any purpose. This Servo is convenient for throttle control on shoulder wing models.
6
6. Please make certain that each connector is fully plugged in and that the Aileron section etc. , and the power supply switch harness is correctly identified. After making certain that the connections are correct according to the above diagram, turn on the transmitter switch and then put the receiver switch to ON position. Move each stick and Trim lever and check to see if the specific Servo is actuated correctly. When each section is tested for movement, please make certain that both the Transmitting and Receiving antennas are fully extended. If the Transmitting antenna is shortened and the Transmitter switch is left ON for more than 5 minutes, the transistors in the Transmitter will be damaged. If the system does not operate after completely assembling the batteries, switch harness and Servos for the receiver and the Transmitter, the problem may be due to damage during shipment. Do not attempt to open any of the units, but return them for exchange.
7
NI-CAD BATTERIES AND RE-CHARGING
FP-4DN, FP-5DN, FP-6DN and FP-5 Transmitters are equipped with eight (8) pen-light type Ni-Cad batteries. For the Receiver & Servos, Four (4) Ni-Cad batteries are provided in the set. Prior to each usage Ni-Cad batteries should be charged for 12 to 15 hours. [. . . ] 11
GUARANTEE
Your NEW FUTABA Digital Proportional R/C system is guaranteed for 180 days from date of purchase against all defects in materials or workmanship. When the attached registration card is returned to us within Ten days of purchase. Guarantee is void if this R/C system has been improperly handled, damaged in a crash or tampered with. The guarantee does not cover the replacement of Plastic Housings or Electronics components by the use of improper voltage. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE FUTABA FP-6DN
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual FUTABA FP-6DN will begin.