User manual FUTABA FP-7UAFS

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual FUTABA FP-7UAFS. We hope that this FUTABA FP-7UAFS user guide will be useful to you.


FUTABA FP-7UAFS : Download the complete user guide (6302 Ko)

Manual abstract: user guide FUTABA FP-7UAFS

Detailed instructions for use are in the User's Guide.

[. . . ] 4 channels --Elevator -> f l a p mixing --Flaperon & aileron differential -Programmable mixing 2 separate systems --Flap -> elevator mixing · TABLE OF CONTENTS SET CONTENTS . 23 ABBREVIATIONS ATV D/R EXP REV F/S PMX 2->6 6->2 SNP DIFF ADJUSTABLE TRAVEL VOLUME DUAL RATE EXPONENTIAL REVERSE FAILSAFE PROGRAMMABLE MIXING ELEVATOR^ FLAP MIXING FLAP -> ELEVATOR MIXING SNAP-ROLL AILERON DIFFERENTIAL FLPR FLTR STRM COMB MOD AUX PCM PPM B. F/S FLAPERON FLAP TRIM SUB TRIM COMBINATION SWITCH MODULATION AUXILIARY PULSE CODE MODULATI PULSE POSITION MODULATION BATTERY FAIL SAFE --1 -- · SET CONTENTS *Specifications are subject to change without prior notice. FP-7UAP · FP-T7UAP ( X 1 ) · FP-TP-FM ( X 1 ) FP-7UAFSS · FP-T7UAF ( X 1 ) Rating 2 s t i c k s , 7 channels, PCM or FM transmitter Transmitting frequency: 72MHz, 50MHz, 35/36MHz, 40/41 MHz or 29MHz band Modulation: FM-PCM/PPM Selectable Power requirement: 9. 6V Nicd battery pack Current drain: 200mA · FP-R129DP ( X 1 ) (Dual Conversion Type) or FP-R137GP (X1) · FP-R128DF ( X 1 ) (Dual Conversion Type) Receiving frequency: 72MHz, 50MHz, 35/36MHz, 40/41 MHz or 29MHz band Intermediate frequency: 1st IF 10. 7MHz, 2nd IF 455kHz (R129DP, R128DF), 455kHz (R137GP) Power requirement; 4. 8V Nicd battery pack (shared with servo) Current drain: 35mA (R129DP), 26mA ( R 1 2 8 D F ) , 25mA (R137GP) Dimensions: 63. 0x37. 8x24. 1mm (R129DP). 63. 8x35. 4x20. 3mm ( R 1 2 8 D F ) (excluding protruding parts), 57x42x24mm (R137GP) Weight: 45g (R129DP), 40g (R128DF), 45g(R137GP) Receiving range: 500m on the ground. 1000m in the air (range differs with the surroundings] Control system: + pulse width control Operating angle: Rotary system, one side 45 or greater (including trim) Power requirement: 4. 8V or 6. 0V (shared with receiver) Current drain: 8mA at 6V (at idle) Output torque; 3kg/cm Operating speed; 0. 22sec/60° Dimensions: 40. 4x1 9. 8x36mm Weight: 44. 4g, 1. 56oz. [. . . ] · The rate setting range is 30% to 110%. Select the CH to which ATV is to be applied with the keys. Direction selection the Direction with the , or The rate described below is set Select R/U: Right or up L/D: Left or down Rate setting Set the rate with the keys. (When the + and -- keys are pressed simultaneously, 100% is set. ) Set for a different CH and direction by repeating steps To D/R The rate can be switched with the Select the CH for which D/R is to be set with the keys. · D/R can be set for CH1 (aileron), CH2 (elevator), and CH4 (rudder). · D/R can be set for each direction D/R switch direction selection Switch to which the the direction for is to of the With this feature you can select which switch position you want for high rate and low rate. ·Related function COMBINATION SWITCH. be set. Set the rate with the keys. When the interference ceases, the HOLD mode is released. F/S function selected CH servo operating position setting Set the flashing "SET" with the keys. display to (F/S function setting) When interference makes reception impossible, the servos move to the position set at the transmitter. When the interference ceases, the F/S function is reset. The channel or for which the F/S function was selected is held in the desired position. At the same time, data is automatically sent to the receiver. ) *The F/S set data is automatically sent every minute. (FP-7UAFSS) *When using the B. F/S function, set the throttle channel F/S function. To PMX1 -10- · FUNCTION AND DATA SETTING Press the [MODE SELECT] To normal display mode PMX1 PROGRAMMABLE MIXING 1 This mixing is useful in correcting bad tendencies of the aircraft and in making operation more pleasant. · The left and right (up and down) mixing rate can be set independently. · Setting range: 0 -- 100% (mixing maximum) Mixing activate/inhibit mode setting Set the mode with the keys. (When the + and -- keys are pressed simultaneously, 0% is set. ) OFF side ON side ToSNP -14 - · FUNCTION AND DATA SETTING Press the [MODE SELECT] To normal display mode SNP SNAP-ROLL Activate/inhibit mode setting Set the mode with the keys. + : Activate -: Inhibit Avalanche and other snap rolls can be performed by switch. R/U: R/D: L/U: L/D: snap roll directions can be Right up snap Right down snap Left up snap Left down snap Select the direction UP RIGHT DOWN LEFT the to the combination of directions to be set. Switch Aileron servo throw setting Set the flashing display to CH1 with the keys. (When the + and -- keys are pressed simultaneously, 100% is set. ) · The throw of the channel 1 (aileron), channel 2 (elevator), and channel 4 (rudder) servos can be set. (Mode in which operation is not performed when the landing gear is down even if the switch is turned on by mistake. ) "1" to "4" is displayed according to the position. 1: R/U 2: R/D 3: L/U 4: L/D Elevator servo throw setting Set the same as Rudder servo throw setting Set the same as Set for each direction of the by repeating steps to SAFETY mode setting Set the to CH5 with the keys. Set the to the direction for which snap roll is to be turned off (direction in which landing gear is down). UP RIGHT Press the -- side of the keys. SNAP ROLL DOWN LEFT F: SAFETY mode released 5L: SAFETY mode set and ON 5F: S A F E T Y mode set and OFF SAFETY mode release Set the to CH5 with the keys. Press the + side of the keys. ToDIFF - 15 -- · FUNCTION AND DATA SETTING Pressthe (MODE SELECT] keys simultaneously To normal display mode DIFF AILERON DIFFERENTIAL Activate/inhibit mode setting Set the mode with the keys. + : Activate -: Inhibit A left and right differential can be applied to the ailerons. (Left and right aileron servos are necessary. ) · The operating channels are CH1 and CH7. Set the CH1 servo direction of operation. (INH: Inhibit state) Set the flashing display to "+" or "--" with the keys. (Channel 1 side selected. ) ·AIL DIFF AND FLAPERON cannot be on simultaneously. The function turned on last has priority. (ON: Activate state) Set the direction of operation with the keys. [. . . ] (When the + and - keys are pressed simultaneously, 0% is set. ) To COMB COMB COMBINATION SWITCH Other D/R switch functions can be combined by aileron D/R switch. Mode setting Set the mode with the keys. · Three modes can be set. 1: Mode 1 2: Mode 2 3: Mode 3 To MOD -- 18 - · FUNCTION AND DATA SETTING · OTHER FUNCTIONS Press the [MODE S E L E C T] To normal display mode MOD MODULATION The modulation can be switched PCM <-> PPM mode. * Select the PCM mode for the FP7UAP and the PPM mode for the FP. 7UAF. select the same mode at the instructor side and student side transmitters. Mode selection Select the mode with the keys. *When the mode was switched, the transmitter power switch is turned off and transmit output is obtained the next time the transmitter power switch is turned on. C:PCM F:PPM When the mode is changed, the display flashes. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE FUTABA FP-7UAFS




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual FUTABA FP-7UAFS will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.