User manual GAGGIA SUP025Y

[. . . ] As the proud owner of the machine, you can now experience the taste of a delicious cup of espresso or cappuccino in the comfort of your own home. When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and/or injury to persons, including the following: 1 Read all instructions and information in this instruction book and any other literature included in this carton referring to this product before operating or using this appliance. 3 To protect against fire, electric shock and personal injury do not immerse cord, plugs or appliance in water or other liquid. 4 Close supervision is necessary when any appliance is used by or near children. [. . . ] This system allows you to obtain an optimal cup of coffee with all types of marketed coffee. The coffee will stop flowing automatically when the preset level is reached (see par. Only turn the grinding control knob, found inside the coffee bean container (Fig. Do not insert ground and/or instant coffee in the coffee bean container. The coffee grinder contains dangerous moving parts; keep fingers and/or other objects away. Before carrying out any operations in the coffee bean container, switch OFF the ON/OFF switch (7) and remove the plug from the wall outlet. The quality and the taste of your coffee depend, in addition to the used blend, also on the grinding coarseness. To use this feature, turn the graduated knob when the coffee grinder is working; the numbers displayed on the knob indicate the grinding coarseness. The manufacturer sets the knob to an average grinding coarseness in the factory: if the ground coffee is too fine, turn the knob toward the higher values; if the ground coffee is too coarse, turn the knob toward the lower values. You should change the grinding position if the coffee does not outflow optimally, specifically: Too fast = grinding too coarse > grind coffee finer; Too slow (drips and/or no flow) = grinding too fine > grind coffee coarser. 3 Adjusting the quantity of coffee per cup Your coffee maker has been programmed to make 2 types of coffee: espresso coffee with the button (23) and weak coffee with the button (24). To adjust the programmed values to the size of your cups, place the cup under the coffee dispenser (13), press the button of the desired type of coffee (23) or (24) and keep it pressed. ⷠBefore dispensing hot water, make sure that the green temperature-ready LEDs (23 and 24) emit a fixed light. Proceed as follows when the appliance is ready to dispense hot water: · When you have obtained the desired quantity of hot water, turn the knob clockwise to shut off the flow. To make 1 coffee, position a single coffee cup under the coffee dispenser spouts and press the button (23) or (24) only once; to make 2 coffees, position two coffee cups under the spouts and press the button (23) or (24) twice. In this operating mode, the appliance automatically grinds and doses the right quantity of coffee; making two coffees requires two grinding and dispensing cycles, which are automatically managed by the machine. After carrying out the prebrewing cycle, coffee Steam can be used to froth the milk for cappuccinos but also to heat beverages. You may select the quantity of coffee (dose) that When the appliance is ready to dispense coffee, press the button (25), the LEDs (23) and (24) switch off. The appliance goes through a preheating period; during this phase, the LED (25) flashes. ⷠBefore dispensing steam, wait for the green temperature-ready LED (25) to light up in a fixed way; this indicates that the correct operative temperature has been reached. ⷠDirect the steam nozzle (14) towards the drip tray and turn the "hot water/steam" knob (16) for a few seconds so that any residual water comes out of the steam nozzle. Fill 1/3 of the vessel that you wish to use to make cappuccino with cold milk. [. . . ] ⷠThe information should be viewed as a guideline to use and upkeep your coffee maker in safety. For additional information or for information on topics not covered or inadequately covered in this book, please contact the authorized service centres or the manufacturer directly. ⷠIn addition, we should mention that these instructions are not a part of a previous or existing agreement, legal contract or similar and that the information is not changed by any other document. The contractual warrantee terms and conditions are not limited or extended based on this instruction book. [. . . ]