User manual GAGGIA SYNCRONY DIGITAL

[. . . ] As the proud owner of the machine, you can now experience the taste of a delicious cup of espresso or cappuccino in the comfort of your own home. When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and/or injury to persons, including the following: 1 Read all instructions and information in this instruction book and any other literature included in this carton referring to this product before operating or using this appliance. 3 To protect against fire, electric shock and personal injury do not immerse cord, plugs or appliance in water or other liquid. 4 Close supervision is necessary when any appliance is used by or near children. [. . . ] ⷠBefore dispensing coffee, check that the water tank and coffee container are full and that the display shows: Place 1 or 2 coffee cups under the coffee spouts; you can adjust the height of the brew unit by moving it up or down manually (Fig. To brew coffee press the coffee brew button (22, 23 or 24); the display will indicate (for example) ENGLISH To dispense 1 coffee, place a single cup beneath the coffee spouts and press the button (22, 23 or 24) only once; to dispense 2 coffees, place two cups beneath the coffee spouts and press the button (22, 23 or 24) twice; the display will show: In this operating mode, the appliance automatically grinds and measures out the right quantity of coffee; making two coffees requires two grinding and dose dispensing cycles, which are automatically managed by the machine. ENGLISH In this way, the appliance will be programmed to brew the quantity of coffee you selected. When the machine is ready to dispense steam, the display will show: The hot water nozzle and tube can reach high temperatures: avoid touching them directly with your hands. ⷠBefore attempting to dispense hot water, make sure that the display shows. When the machine signals that it is ready to brew coffee, carry out the following steps. Direct the steam tube (14) over the drip tray (12), place a cup or other suitable receptacle beneath the steam nozzle. Open the "Hot water/steam" knob (16) for a few instants to discharge any residual water from the steam nozzle; in a short while only steam will issue from the tube. Fill the receptacle you wish to use for making cappuccino to 1/3 with cold milk. For best results when making cappuccinos, the milk and the cup used should be cold. ⷠImmerse the steam nozzle into the milk to be frothed and turn the knob (16); turn the container slowly with up-down movements to achieve uniform frothing (Fig. ⷠWhen you have finished dispensing steam, turn off the function by pressing the button (26). Steam can be used to froth the milk for cappuccinos and also to heat beverages. The hot water nozzle and tube can reach high temperatures: avoid touching them directly with your hands. ⷠWhen the machine is ready to brew coffee, press the button (26). 1 Switching from steam to coffee ⷠWhen you switch from the steam dispensing function to the coffee brewing function, the display will show: In order to make coffee, you must discharge ENGLISH some water; place a cup or other suitable receptacle beneath the steam nozzle. Switch off the appliance by moving the ON/ OFF switch (7) to the "O" position and remove the plug from the wall outlet. Remove the brew unit, holding it by its handle and pressing the "PRESS" button (Fig. 15) · Make sure that the two steel filters are free from any coffee residues. The top filter can be removed by unscrewing the plastic pin anticlockwise using the key provided (Fig. ⷠRefit the filter and carefully screw the plastic pin back on using the key provided. ⷠHolding it by its handle, insert the brew unit into its housing until it snaps into place (Fig. [. . . ] Important: if you do not wish to reset the counter, press "ESC". important: after routine descaling , it is recommended to reset the counter. The machine can be programmed to switch automatically from the At this point fill the water tank. The timer starts counting from zero after every This function allows you to restore the default machine operating parameters set by the This instruction book may not be photocopied or translated into other languages without the explicit written consent of the manufacturer. [. . . ]