User manual GARMIN G1000 MOONEY PRIMARYFLIGHTDISPLAY PILOTS GUIDE M20M M20R

[. . . ] G1000 TM primary flight display pilot's guide for Mooney M20M & M20R Record of Revisions Revision Date of Revision Revision Page Range A 05/23/05 3-1 ­ 3-51 Description Initial release. Garmin G1000 PFD Pilot's Guide for Mooney M20M & M20R 190-00443-01 Rev. A INTRODUCTION 3. 1 INTRODUCTION This Pilot's Guide describes the major features of the Primary Flight Display (PFD) on the G1000 Integrated Cockpit System installed on the Mooney aircraft. During normal operation, the left display is configured as a Primary Flight Display. The PFD provides increased situational awareness by replacing the traditional "six pack" of instruments in the pilot's panel with an easy-to-scan display that provides a large horizon, airspeed, attitude, altitude, vertical speed, navigation, communication, annunciation, terrain, traffic and lightning information. [. . . ] Press the TOPO softkey again to remove topo data from the map. NOTE: When topo data is removed from the display, all cartographic data is automatically removed and the Jeppesen Nav Data is presented on a black background. To enable/disable terrain data: 1. Press the TERRAIN softkey to display color-coded terrain tiles, which are based upon the aircraft current altitude. A mountain icon appears above the zoom range in the lower right corner of the map, showing that terrain is selected. · Red (warning) ­ Land elevation is within 100 ft or above the aircraft current altitude. · Yellow (caution) ­ Land elevation is greater than 100 ft to 1, 000 ft below aircraft altitude. · Black ­ Land elevation greater than 1, 000 ft below aircraft altitude. Press the TERRAIN softkey again to remove the terrain data from the map. NOTE: Terrain data is not displayed when the aircraft latitude is greater than 75° North or 60° South. NOTE: Refer to the Appendix for more details about terrain. 190-00443-01 Rev. A Garmin G1000 PFD Pilot's Guide for Mooney M20M & M20R 3-31 SUPPLEMENTAL FLIGHT DATA To enable/disable Stormscope (optional), NEXRAD (optional), or XM lightning (optional) data: 1. Press the STRMSCP (optional), NEXRAD (optional), or XM LTNG (optional) softkey to display weather information. Press the STRMSCP, NEXRAD, or XM LTNG softkey again to remove the weather information from the map. NOTE: Refer to the G1000 Optional Equipment Pilot's Guide for more details about the weather options. WORKING WITH MENUS Much of the G1000 operation is accomplished using a menu interface. The G1000 has a bezel-mounted dedicated MENU key that, when pressed, displays a context-sensitive list of options. This option list allows the pilot to access additional features or make setting changes which specifically relate to the currently displayed window. Some menus provide access to additional sub-menus that are in turn used to view, edit, select and review options. Once the Page Menu window is displayed, turn the FMS knob to scroll through a list of available options (a scroll bar always appears to the right of the window when the option list is longer than the window) and press the ENT key to select the desired option. The CLR key may be pressed to remove the menu and cancel the operation. Pressing the FMS knob also removes the displayed menu. To pan the map: NOTE: The joystick on the PFD operates independently from the one on the MFD. 1. 2. 3. Push in the joystick to display the panning pointer. This allows the pilot to move the map beyond its current limits without adjusting the range. Push in and move the joystick to pan the map Figure 3. 6. 5 Page Menu ­ No Options With NRST Window Displayed in the general direction of the desired location. When the pointer is placed on an object, the name of the object is highlighted for approximately 4 seconds (even if the name was not originally displayed on the map). This feature applies to everything displayed on the map except for route lines. Push in the joystick again to cancel the panning function and return to the present position on Figure 3. 6. 6 Page Menu ­ Options With FPL Window Displayed the map. NOTE: The airspace boundary stays highlighted for approximately 4 seconds before returning to normal shading. [. . . ] Turn the FMS knob to select the desired runway, then press the ENT key. Turn the FMS knob to select the desired transition, then press the ENT key. With `LOAD?' highlighted, press the ENT key. 5. 190-00443-01 Rev. A Garmin G1000 PFD Pilot's Guide for Mooney M20M & M20R 3-47 SUPPLEMENTAL FLIGHT DATA This page intentionally left blank. 3-48 Garmin G1000 PFD Pilot's Guide for Mooney M20M & M20R 190-00443-01 Rev. [. . . ]