User manual GARMIN G1000 MOONEY SYSTEMOVERVIEW M20

[. . . ] The GMA 1347 also controls manual display reversionary mode (large red button). The GMA 1347 communicates with both GIA 63s using RS-232 digital interface. 2. 2 LRU DESCRIPTIONS · GDU 1040 ­ The GDU 1040 has a 10. 4-inch LCD display with 1024 x 768 resolution. The left display is configured as a Primary Flight Display 190-00442-00 Rev. A Garmin G1000 System Overview for Mooney M20M & M20R 2-1 SYSTEM OVERVIEW · GIA 63 ­ The GIA 63 is the central `Integrated Avionics Unit' of the G1000 system. [. . . ] · (3) NAV Frequency Selector ­ The concentric knobs tune the MHz (large) and kHz (small) standby frequencies for the NAV receiver. Press on the small knob to toggle the tuning cursor (cyan box) between the NAV1 and NAV2 fields. When this knob is pressed, a window displaying a digital heading momentarily appears to the left of the Heading Indicator and the heading bug synchronizes with the compass lubber line. · (6) CRS/BARO Selector ­ The large knob sets the altimeter barometric pressure and the small knob adjusts course. Course is adjustable when the HSI is in NAV 1 & 2 or OBS/SUSP modes only). Pressing the small knob centers the CDI on the currently selected VOR. · (7) COM Frequency Selector ­ The concentric knobs tune the MHz (large) and kHz (small) standby frequencies for the COM receiver. Pressing the small knob toggles the tuning cursor (cyan box) 2-6 · · · · · · between the COM 1 and COM 2 fields. (8) COM Frequency Toggle Key ­ Swaps the standby COM frequency and the active COM frequency. Pressing and holding this key for ten seconds automatically makes the 121. 5 MHz emergency frequency the active frequency. Audio volume increase and decrease is shown in the field as a percentage. (10) DIRECT-TO Key ( ) ­ Allows the user to enter a destination waypoint and establish a direct course to the selected destination (specified by identifier, chosen from the active route, or taken from the map cursor position). (11) FPL Key ­ Displays the active Flight Plan Page for creating and editing the active flight plan or accessing stored flight plans. To immediately display the Navigation Map Page, press and hold CLR (MFD only). (13) FMS Knobs ­ The concentric knobs are used to select the page to be viewed (only on the MFD)-- the large FMS knob selects a page group (MAP, WPT, AUX, NRST) while the small FMS knob selects a specific page within the page group. When the cursor is on, data may be entered in the different windows using a combination of the small and large FMS knobs. The small FMS knob is used to select individual characters for the highlighted cursor location. When the G1000 displays a list of information that is too long for the display screen, a scroll bar appears along the right side of the display. The scroll bar graphically indicates the number of additional items available within the selected category. 190-00442-00 Rev. A Garmin G1000 System Overview for Mooney M20M & M20R SYSTEM OVERVIEW Press the FMS/CSRS to activate the cursor and turn the large FMS knob to scroll through the list. This options list allows the user to access additional features or make settings changes that relate to certain pages. (15) PROC Key ­ Selects approaches, departures and arrivals from the flight plan. [. . . ] Both displays offer control over COM and NAV frequency selectors, as well as heading, course/baro and altitude reference functions. On the left of the MFD display, an Engine Indication System (EIS) cluster shows graphical depictions of engine and airframe instrumentation. Figure 2. 7. 1 gives 2-10 Reversionary display mode may also be manually activated by the pilot, if the system fails to detect a display problem. The reversionary mode is activated manually by pressing the large red button on the bottom of the GMA 1347. [. . . ]