User manual GATEWAY 6010GZ

[. . . ] The battery used in this device may present a fire or chemical burn hazard if mishandled. Keep away from children. 7 Slide the battery lock to the lock position. 10 Open the LCD panel and press the power button. To replace the battery: 1 If your notebook is on and is connected to AC power, go to Step 2. - OR If your notebook is on and is not plugged into an AC outlet, save your work and turn off the notebook. [. . . ] Do not lay components on the outside of antistatic bags because only the inside of the bags provide electrostatic protection. Never slide components over any surface. Screws · www. gateway. com 1 Replacing the Hard Drive Kit 8 If your new hard drive already includes the hard drive cover, go to Step 13. -ORIf you need to move the hard drive cover from your old hard drive to your new hard drive, go to Step 9. 9 Remove the four screws that secure the hard drive to the hard drive cover. 11 Place the new drive, label side up, onto the cover so the screw holes line up. 13 Slide the new hard drive kit into your notebook, then replace the cover screws. 17 For instructions on installing Windows, your drivers, and your applications, see the instructions that were included in the restoration booklet. Screws Screws Technical Support See the label on the bottom of the notebook for Customer Care information. 10 Remove the cover from the old drive. Safety, Regulatory, and Legal Information See your user guide for important safety, regulatory, and legal information. © 2005 Gateway, Inc. Gateway, Gateway Country, the Gateway stylized logo, and the black-and-white spot design are trademarks or registered trademarks of Gateway, Inc. All other brands and product names are trademarks or registered trademarks of their respective companies. 2 www. gateway. com Replacing the Keyboard Replacing the Keyboard Tips & Tricks You need a small Phillips and a small flat-blade screwdriver to replace the keyboard. Screw Preventing static electricity discharge The components inside your notebook are extremely sensitive to static electricity, also known as electrostatic discharge (ESD). ESD can permanently damage electrostatic discharge-sensitive components in your notebook. Warning To avoid exposure to dangerous electrical voltages and moving parts, turn off your notebook, remove the battery, and unplug the AC adapter, modem cable, and network cable before replacing a component. 8 With a small Phillips screwdriver, remove the two hinge cover screws and put them in a safe place. Warning To prevent risk of electric shock, do not insert any object into the vent holes of your notebook. Screw Screw Before working with notebook components, follow these guidelines: · · Avoid static-causing surfaces such as carpeted floors, plastic, and packing foam. Remove components from their antistatic bags only when you are ready to use them. Do not lay components on the outside of antistatic bags because only the inside of the bags provide electrostatic protection. Wear a grounding wrist strap (available at most electronics stores) and attach it to a bare metal part of your workbench or other grounded connection. Touch a bare metal surface on your workbench or other grounded object. 11 Insert the small flat-blade screwdriver under the right end of the keyboard cover and gently pry it up. 9 Insert the small flat-blade screwdriver under the bottom of each hinge cover and gently pry it up. · · · Removing the keyboard To remove the keyboard: 1 Follow the guidelines under "Preventing static electricity discharge. " 2 Turn off your notebook. 5 Turn your notebook over so the bottom is facing up, then remove the battery. For more information, see "Changing Batteries" in your user guide. 2 Make sure the black keyboard connector clip is fully moved toward the front of the notebook, insert the cable into the connector, then slide the black clip to lock the connector in place. See the label on the bottom of the notebook for Customer Care information. Safety, Regulatory, and Legal Information See your user guide for important safety, regulatory, and legal information. [. . . ] Do not lay components on the outside of antistatic bags because only the inside of the bags provide electrostatic protection. www. gateway. com 1 Replacing the Wireless Network Card 7 Unplug the two antenna cables. 10 Hold the new module at a 30-degree angle and press it into the empty slot. If the module does not fit, make sure that the notch in the module lines up with the tab in the module slot. 11 Move the antenna wires out of the way, then press the module down until it clicks into place. [. . . ]