User manual GATEWAY DC-M40

[. . . ] DC-M40 digital camera user's guide READY SPECIAL FEATURES This digital camera has the following features. · · · · · High resolution of 4. 1 mega pixels 3X optical and 2X digital zoom lens Movie clip recording function Voice Recording and Playback for still image An easy and fast PC interface with USB Storage Driver & Digital Image. Regulatory compliance statements United States of America Federal Communications Commission (FCC) Unintentional emitter per FCC Part 15 This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception. [. . . ] 6. Press the MENU button to cancel the menu display. STILL IMAGE mode Reference Explanation of SHARPNESS sub menu · SOFT: This gives smooth edges and the final image will have a soft appearance. · NORMAL: This setting will give a standard finish to the final image. · HARD: This will give the image a crisp and clear appearance. 49 ADVANCED SETTING UP THE SHOOTING FUNCTION LCD · You can adjust the LCD brightness. 2. Press the MENU button and press the UP ( ) / DOWN ( ) button and select [LCD ]. 4. The LCD BRIGHTNESS SELECTION SCREEN will be displayed by pressing the RIGHT ( ) button. 5. Select the desired brightness value by pressing the UP ( ) / DOWN ( ) button. 6. After selecting the desired brightness value, press the OK button to confirm the setting. 7. Press the MENU button to cancel the menu display. REC. TIME · You can select available recording time. Select the desired recording time by pressing the UP ( ) / DOWN ( ) button. After selecting the desired recording time, press the OK button to confirm the setting. Press the MENU button to cancel the menu display. MOVIE CLIP mode 50 ADVANCED SETTING UP THE PLAY BACK FUNCTION Starting PLAY Mode · Turn the camera on and select PLAY mode ( ) on the mode dial. · You can setup the PLAY mode function by using the camera buttons and LCD monitor. · PLAY mode functions are listed below. Camera button THUMBNAIL, ZOOM DELETE VOICE RECORDING PLAY & PAUSE LCD monitor Play back Print setting SLIDE SHOW, LCD brightness DELETE ALL QUANTITY, INDEX CANCEL Reference · The last image stored on the CF CARD will be displayed on the LCD monitor. · The LCD monitor will remain in operation until the camera is switched off. The menu will not display on the LCD monitor under the following circumstances: · When another button is being pressed. · When there is no battery capacity. 51 ADVANCED SETTING UP PLAY BACK FUNCTIONS Setting up play back function by using the camera button · The PLAY mode can be set using the camera button. THUMBNAIL / ZOOM button · You can view up to 6 images at a time by using the THUMBNAIL function. Rotate the mode dial to the PLAY mode ( ) and the last image displays on the LCD monitor. The thumbnail display will highlight the last 6 images on the LCD monitor. Press the THUMBNAIL button Highlighted image (selected image) SINGLE DISPLAY MODE Thumbnail display mode 3. When viewing a thumbnail image, press the [ZOOM ] button and the selected shot will show in single display mode. 52 ADVANCED SETTING UP PLAY BACK FUNCTIONS ZOOM button button to · When viewing a single image in PLAY mode, use the zoom enlarge the selected image. 2X scale of enlargement 1. Enlarge the image to 2X scale of enlargement by using the ZOOM button. Press the ZOOM button to zoom back to the original full-sized image. Reference · If an image is enlarged, the ratio indicator will display on the upper-left side of the LCD monitor. · If an image is enlarged, a loss of quality may occur. MENU button · Pressing the MENU button will display the PLAY mode menu. [. . . ] Click [Stop] in the [Unplug or Eject Hardware] window and click [Ok] on the next windows. Click [Device Manager] Universal serial bus controller USB Mass Storage Device] and click the right mouse button. Restart the computer. 91 SOFTWARE CONNECTING THE CAMERA FOR MAC Connecting the USB cable to the camera for MAC · The USB port has to be on the Macintosh or keyboard. Switch the camera on. How to install and use the USB driver for MAC · Setting up the USB Driver for MAC The USB Driver for MAC is not included with the Application CD as MAC OS support the camera driver. [. . . ]