User manual GE DIGIA II

[. . . ] Digia II User Manual Copyright Copyright © 2006, GE Security, Inc. This document may not be copied in whole or in part or otherwise reproduced without prior written consent from GE Security except where specifically permitted under US and international copyright law. Document number/revision: 1058007A (December 2006). Disclaimer The information in this document is subject to change without notice. ("GE Security") assumes no responsibility for inaccuracies or omissions and specifically disclaims any liabilities, losses, or risks, personal or otherwise, incurred as a consequence, directly or indirectly, of the use or application of any of the contents of this document. [. . . ] Camera Record Schedule Alarms Network Display System Information Chapter 3 Setup 11 Camera Figure 5 shows the Camera menu options. Figure 5. Camera Digia II Menu - Camera << Camera 1 Title Recording Frame Rate Quality Level Covert Sequence List DWELL time Brightness Contrast Saturation CH01_ _ _ _ _ Continuous 1 f/s 6-Highest >> 03 Sec(s) 50 % 50 % 50 % Select EXPORT to Copy Settings Select DISPLAY to Paste Settings Table 1. Camera submenu Menu item Camera # Title Recording Frame rate Quality level Covert Sequence list Dwell time Brightness Contrast Saturation Select EXPORT to copy settings. Select DISPLAY to paste settings. Description Each camera has its own submenu. The number of submenus depends on how many cameras your Digia II is capable of supporting. Choose the frame rate for this camera from 1 to 30 frames per second (fps). Press the Export button to copy the settings from this camera submenu to the clipboard. If you copied settings from another camera submenu, press DISPLAY to paste those settings in the appropriate places on the current submenu. 12 Digia II User Manual Record Figure 6 shows the Record submenu. Figure 6. Record Digia II Menu - Record Resolution Pre-Alarm Audio Auto Delete Mode Disk Overwrite 2CIF Disable Continuous Table 2. Record submenu Menu item Resolution Pre-alarm Audio Auto delete mode Disk overwrite Description Choose the resolution you want to record at. Choose between continuous or no overwrite. Chapter 3 Setup 13 Schedule The Schedule submenu has submenus of its own. Those menus are Time periods and a schedule menu for each camera. Time periods Figure 7 shows the Time periods submenu. Figure 7. Time periods Digia II Menu - Schedule << # 1 2 3 4 5 6 7 8 Time Periods Schedule Disable Disable Disable Disable Disable Disable Disable Disable Start 08:00a 12:00p 12:00p 12:00p 12:00p 12:00p 12:00p 12:00p End 06:00p 08:00p 12:00a 12:00a 12:00a 12:00a 12:00a 12:00a >> Table 3. Time periods submenu Menu item # Schedule Start End Description The list of schedules, in numerical order. Choose from Disable, Weekday, Weekend, Daily, and Monday through Friday. Set the end time. 14 Digia II User Manual Camera # (1 - 16) Figure 8 shows the Camera submenu. Note: Your number of cameras will depend on which model of Digia II you have and how many cameras or channels it is capable of. Figure 8. Camera schedule Digia II Menu - Schedule << # 1 2 3 4 5 6 7 8 Schedule Disable Disable Disable Disable Disable Disable Disable Disable Camera Start 08:00a 12:00p 12:00p 12:00p 12:00p 12:00p 12:00p 12:00p 1 End 06:00p 08:00p 12:00a 12:00a 12:00a 12:00a 12:00a 12:00a IPS 1 1 1 1 1 1 1 1 >> QL 6 6 6 6 6 6 6 6 Table 4. Camera schedule submenu Menu item IPS QL Description Set between 0 and 3. Set between 1 and 6. Chapter 3 Setup 15 Alarms Figure 9 shows the Alarms submenu. Figure 9. Alarms Digia II Menu - Alarms << Alarm 1 Alarm Alarm Frame Rate Quality Level Alarm Duration Sensor Type Event Buzzer Alarm to Full Screen eMail Notification Video Loss Motion Detection Motion Sensitivity >> Disable 10 f/s 6-Highest 05 Sec(s) NC Disable 7 Select EXPORT to Copy Settings Select DISPLAY to Paste Settings Table 5. Alarms submenu Menu item Alarm # Alarm Alarm frame rate Quality level Alarm duration Sensor type Event buzzer Alarm to full screen Email notification Video loss Motion detection Motion sensitivity Motion detection grid Description The current alarm being edited. Check this box if you want the video to become full screen when the alarm is triggered. Check this box if you want the Digia II to send an e-mail to a predetermined e-mail address when the alarm is triggered. If you set it to partial, it will take you into the motion detection grid. Use the directional arrows to move the highlight square to a desired area. When a cell is on, that area will be monitored for motion detection. 16 Digia II User Manual Network The Network submenu has three of its own submenus. They are Network configuration, Network email, and Network DDNS. Network configuration Figure 10 shows the Network configuration submenu. Figure 10. [. . . ] The unit distributes these frames across all the enabled channels evenly (when the recording mode is set to continuous, schedule, or alarms) so that if you are recording at 2CIF (60 fps) with four channels enabled, each channel will be capable of recording up to 15 fps. By default, all channels are enabled and recording at 2CIF resolution. If you have a 4 channel unit, you can either: · · Disable two of the four channels to be able to record at 30 fps on any channel at the default resolution of 2CIF; or, Change the recording resolution from 2CIF to CIF. If you decide to record at D1 resolution on that same four channel unit, then you will need to disable three of the four channels to be able to record at 30 fps. When you export video, you should insert the USB device into the USB port prior to the final step. [. . . ]