User manual GEMINI CDX-02

[. . . ] OVERLOADING: Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. OBJECT AND LIQUID ENTRY: Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. SERVICING: Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. DAMAGE REQUIRING SERVICE: Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: · If the product does not operate normally by following the operating instructions. [. . . ] If this product is equipped with a three-wire grounding type plug, a plug having a third (grounding) pin, it will only fit into a grounding type power outlet. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. REPLACEMENT PARTS: When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. SAFETY CHECK: Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. WALL OR CEILING MOUNTING: The product should not be mounted to a wall or ceil ing. HEAT: The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. POWER-CORD PROTECTION: Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. This state of the art professional CD player is backed by a three year warranty, excluding lasers. Prior to use, we suggest that you carefully read all the instructions. Plug the other end of the RCA connectors into any available line level input jacks on your mixer. If you are connecting the CDX-02 through a receiver, you can plug the RCA connectors into the CD or AUX INPUT JACKS on your receiver. If there are no CD or AUX INPUTS, use any line level (not phono) inputs. Large blue backlit LCD display Three-way time selection Single/auto-continuous play modes Beat per minute counter tap button Precise rubber jog wheels with finger grips Pitch bend with jog wheel or buttons Stutter play for accurate cue point selection Instant-start & cue with preview Fast track & song searching CD-R compatible POWER: After making sure that the VOLTAGE SELECTOR (1) switch, found on the rear panel, is properly set, plug the unit in and press the POWER (5) button. DISC TRAY: The DISC TRAY (7) is where the CD is held during loading, unloading and playback. Note: Do not force the DISC tray to close, excessive force will damage the CD mecha nism, use the open/close (8) buttons only. OPEN/CLOSE BUTTON: Press OPEN/CLOSE (6 & 8) to load or remove a CD from the DISC TRAY. : The LIQUID CRYSTAL DISPLAY (12) shows the track number, pitch value, single-auto cue, continue (for continuous play), and 4 different time displays. These time displays are time elapsed on the track, time remaining on the disc, the last 30 second outro of the track, and time remaining on the track. The display flashes slowly when the track has 30 seconds remaining and pulses rapidly when playing time is down to 15 seconds. PLAY/PAUSE: Each press of the PLAY/PAUSE BUTTON (10) causes the operation to change from play to pause or from pause back to play. CUE: With the unit in the PLAY mode (PLAY/PAUSE LED is green) and after the cue point has been programmed, pressing CUE (11) will immediately pause the track at the programmed CUE point (the CUE LED glows blue). [. . . ] Press the cue button and you will begin at the beginning of your selected track. Specifications and design are subject to change without notice for purpose of improvement. To fine tune your pre-programmed cue point, push the CUE (11) button and the CD will return to the cue point you programmed in step #2. Use the SEARCH DIAL (9) to move forward or backward to find the proper Cue point. [. . . ]