User manual GEMINI CFX-50

[. . . ] POWER-CORD PROTECTION: Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. OUTDOOR ANTENNA GROUNDING: If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. LIGHTNING: For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. [. . . ] ANTI-SHOCK BUFFER MEMORY: With 12 SECONDS OF ANTISHOCK BUFFER MEMORY, each side of the CD player stores 6 seconds of future play to ensure that any harsh movement or bumping of the unit will not interrupt play and play will continue smoothly. LED Target Light for Draw Mechanism Variable Pitch Control (4%, 12%, 24%, & 100%) 5 DSP Effects With Time & Ratio Parameter Control New "State of the Art" Master Tempo With, Fully Functional Pitch Large LCD Screen with Blue LED Backlight & Dimmer Control Direct Access Keypad with Full Programmable Feature POWER: After making sure that the VOLTAGE SELECTOR (1) switch, found on the rear panel, is properly set, plug the unit in and press the POWER (6) button. DISC TRAY: The DISC TRAY (7) is where the CD is held during loading, unloading and playback. STOP: Press the STOP (8) button to STOP a CD in PLAY mode and to also load or remove a CD from the DISC TRAY (7). Do not use this CD Player at temperatures below 41°F/5°C or higher than 95°F/35°C. The apparatus should not be exposed to dripping or splashing and no objects filled with liquids such as vases should be placed on the apparatus. When disconnecting the power cord from an AC outlet, always grasp it by the plug. To prevent electric shock, do not remove the cover or the bottom screws. DIMMER: Turn the DIMMER (9) to the right to increase brightness of the DISPLAY (10), and push it in to lock the setting. DISPLAY: The DISPLAY (10) shows the track number, pitch value, singleauto cue, continue (for continuous play), and 3 different time displays. These time displays are time elapsed on the track, time remaining on the disc and time remaining on the track. The display flashes slowly when the track has 15 seconds remaining and pulses rapidly when playing time is down to 5 seconds. PLAY/PAUSE : Each press of the PLAY/PAUSE BUTTON (12) causes the operation to change from play to pause or from pause back to play. CUE/PREVIEW: With the unit in the PLAY mode and after the CUE POINT has been programmed, pressing CUE/PREVIEW (13) will cause the CD player to enter the PAUSE mode at the programmed CUE POINT. Holding down the CUE/PREVIEW (13) button changes the function to PREVIEW and starts the CD from the programmed CUE POINT. releasing the CUE/ PREVIEW (13) button will return the CD laser to the preset CUE POINT. Since the CFX-50 is a dual CD player, most of the functions and controls are duplicated on both sides of the CD player. To eliminate confusion and to make the drawings easier to understand, we will only number the left side functions and controls. Place the head of a screwdriver in the center of the VOLTAGE SELECTOR SWITCH (1) found on the rear panel. SEARCH : The SEARCH (15) buttons are used to move forward or reverse while in play or pause mode. TIME: The TIME BUTTON (16) switches the time display between the three available choices listed under DISPLAY (10). B-EDIT: After a LOOP has been memorized you can change the length of the LOOP by pressing B-EDIT (21) then use the JOG WHEEL (24) to adjust the length. [. . . ] Just press MEMO (23) then select any 1 of the 5 CUE POINTS (CUE 1-5) to set a CUE POINT. Once you set a MEMO CUE POINT you can return to that CUE by pressing it again. if the CD is PLAYING it will play from the CUE POINT and if the CD is PAUSED the CUE POINT will be PAUSED as well. MEMO POINTS are locked in memory until that CD is ejected from the CD player. [. . . ]