User manual GEMINI PS-04 (2)

[. . . ] CAUTION: This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other equipment. To prevent electromagnetic interference with electric appliances such as radios and televisions, use shielded cables and connectors for connections. the exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. The lightening flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] Use the LN SWITCH (23) to toggle from PH1/LN1 (18) to LN2 (17) on this channel. Once you've selected the proper line, slowly raise the CH1 FADER CONTROL (29) to a comfortable level. You can further modify the sound output of this channel by adjusting the rotary GAIN (24), HIGH (25), MID (27), LOW (26) controls located to the left of the CH1 FADER CONTROL (29). CH2: To bring this channel into PGM, you must first decide which line will be in use. Use the LN SWITCH (30) to toggle from PH2/LN3 (14) to LN4 (13) on this channel. Once you've selected the proper line, slowly raise the CH2 FADER CONTROL (36) to a comfortable level. You can further modify the sound output of this channel by adjusting the rotary GAIN (31), HIGH (32), MID (34), LOW (33) controls located to the left of the CH2 FADER CONTROL (36). CH3: To bring this channel in to PGM, you must first decide which line will be in use. Use the LN SWITCH (37) to toggle from PH3/LN5 (10) to LN6 (9) on this channel. Slowly raise the CH3 FADER CONTROL (43) to a comfortable level, once you've selected the proper line. You can further modify the sound output of this channel by adjusting the rotary GAIN (38), HIGH (39), MID (41), LOW (40) controls located to the left of the CH3 FADER CONTROL (43). Do not expose this unit to direct sunlight or a heat source such as a radiator or stove. When moving this equipment it should be placed in its original carton and packaging. Before plugging this unit into any outlet, make sure that the VOLTAGE SELECTION SWITCH (1) is set to the proper voltage. To change the selection, unscrew the hard plastic protective top with a Phillips head screw driver. Then use a flat head screw driver to move the switch to the proper selection (115V/230V). Plug into the rear panel POWER CORD (2) jack before plugging it into a proper power source. The PS-04 has four outputs located on the rear panel: - The MASTER RCA OUTPUT (5) connects the mixer to your main amplifier using standard audio cables with RCA-type conectors. - The BALANCED MASTER OUTPUT (8) connects the mixer to your main amplifier using standard cables with 1/4" connectors. CUE: By connecting a set of headphones to the HEADPHONE (22) jack, you can monitor any or all channels. With the VU MODE SWITCH (49) you may monitor the output level of the CUE and PGM when the switch is UP. When this mode is engaged the CUE will be located on the left of the VU METER (50), while the PGM will be located on the RIGHT. [. . . ] - Mezclador de 10", 3 canales estéreo - Entradas RCA para 6 línea, 3 convertible phono/línea - Salidas RCA de master, record, y zona - Salida balanceada jack ¼" - Triple conexión de masa para fácil conectividad PASS: All effects are cancelled and the aduio signal runs clear of effects. aUTO PAN: Stereo signal transfers from left to right and right to l e ft automatically. TRANCE: Modulates the frequency sound by giving the waveform a triangular shape. pHASER: Type of flanger that creates phaser effect by adding phase lagged sound. [. . . ]