User manual GORENJE WHI943A3XGB

[. . . ] Manglende overholdelse af kravene for rengøring af emhætten, og for udskiftning og rengøring af filtrene, medfører brandfare. Elektrisk og elektronisk udstyr indeholder materiale, komponenter og stoffer, der kan være skadelige for menneskers sundhed og for På den vandrette del skal røret have en let stigning (cirka 10°) for at lette bortledning af luften udenfor lokalet. Bemærk: for korrekt brug af denne funktion, følg først , , Forordning af parametre for automatisk funktion" (se paragraf). Tryk en eller flere gange i træk for at vælge tiden for senere slukning, som der ønskes (10-20-30 minutter) Bemærk: for korrekt brug af denne funktion, følg først , , Forordning af parametre for automatisk funktion" (se paragraf). [. . . ] Use a duct with as few elbows as possible (maximum elbow angle: 90°). filter version One active charcoal filter is needed for this and can be obtained from your usual retailer. The filter removes the grease and smells from the extracted air before sending it back into the room through the upper outlet grid. iNSTALLATION The minimum distance between the supporting surface for the cooking equipment on the hob and the lowest part of the range hood must be not less than 55cm from electric cookers and 65cm from gas or mixed cookers. If the instructions for installation for the gas hob specify a greater distance, this must be adhered to. electrical connection The mains power supply must correspond to the rating indicated on the plate situated inside the hood. If provided with a plug connect the hood to a socket in compliance with current regulations and positioned in an accessible area, after installation. If it not fitted with a plug (direct mains connection) or if the plug is not located in an accessible area, after installation, apply a double pole switch in accordance with standards which assures the complete disconnection of the mains under conditions relating to over-current category III, in accordance with installation instructions. Before re-connecting the hood circuit to the mains supply and checking the efficient function, always check that the mains cable is correctly assembled. Very heavy product; hood handling and installation must be carried out by at least two persons. before beginning installation: · Check that the product purchased is of a suitable size for the chosen installation area. This/these is/are to be mounted only if you want lo use the Check (for transport reasons) that there is no other supplied material inside the hood (e. If possible, disconnect and move freestanding or slide-in range from cabinet opening to provide easier access to rear wall/ceiling. Otherwise put a thick, protective covering over countertop, cooktop or range to protect from damage and debris. Cover that surface with a protective covering and place all canopy hood parts and hardware in it. In addition check whether near the installation area of the hood (in the area accessible also with the hood mounted) an electric socket is available and it is possible to connect a fumes discharge device to the outside (only suction version). Installation of an electric socket and/or a hole for the passage of the discharge tube). Expansion wall plugs are provided to secure the hood to most types of walls/ceilings. However, a qualified technician must verify suitability of the materials in accordance with the type of wall/ceiling. The wall/ceiling must be strong enough to take the weight of the hood. It is recommended that the cooker hood suction is switched on for 5 minutes prior to cooking and to leave in operation during cooking and for another 15 minutes approximately after terminating cooking. Note: After about a minute of inactivity (suction and lights), the hood will automatically switch to standby. [. . . ] Setting of Automatic Operation parameters For correct use of the automatic operation, perform , , Hood Calibration". Hood Calibration With the display on (ON) and the suction off (OFF), press button T3 for 3 seconds. The suction speed (power) 2 starts functioning and button T3 flashes to indicate that hood calibration is initiated and it will last for approx. Note: to interrupt the calibration, press T3 for 5 seconds; the calibration will be invalidated and should therefore be repeated. [. . . ]