User manual GRANDSTREAM HT488

[. . . ] Grandstream Networks, Inc. HT488 FXS/FXO Port IAD HT488 User Manual Firmware Version 1. 0. 3. 86 www. grandstream. com support@grandstream. com TABLE OF CONTENTS HT488 USER MANUAL WELCOME. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 SAFETY COMPLIANCES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Blind Transfer Refer to section above for procedure to perform Blind Transfer. Busy Call Forward To use this feature, dial "*90", wait for the dial tone. Then dial the forward number ended with #, wait for dial tone, hang up. Cancel Busy Call Forward To cancel "Busy Call Forward", dial "*91" and get the dial tone, then hang up Delayed Call Forward To use this feature, dial "*92", wait for the dial tone. Then dial the forward number ended with #, wait for dial tone, hang up. Cancel Delayed Call Forward To cancel this Forward, dial "*93" and get the dial tone, then hang up When in conversation, this action will switch to the new incoming call if there is a call waiting beep. When in conversation and there is no call waiting, this action will switch to a new channel for a new call. *73 *87 *90 *91 *92 *93 Flash/Hook LED Light Pattern Indication TABLE 6: HT488 LED DEFINITIONS RED LED always indicates not normal status DHCP Failed or WAN No Cable HT488 fails to register Firmware Upgrading Device Malfunctions GREEN LED indicates normal working status Message Waiting Indication RINGING RINGING INTERVAL In Conversation Grandstream Networks, Inc. Button flashes every 2 seconds Button flashes at 1/10 second Button flashes every second Green light steady on HT488 User Manual Firmware 1. 0. 3. 86 Page 16 of 31 Last Updated: 7/2007 Button flashes every 2 seconds (if DHCP is configured) Button flashes every 2 seconds (if SIP server is configured) Button flashes every 2 seconds Red light steady on CONFIGURATION GUIDE CONFIGURING HT488 THROUGH VOICE PROMPT DHCP MODE Follow Table 3 with voice menu option 01 to enable HT488 to use DHCP. STATIC IP MODE Follow Table 3 with voice menu option 01 to enable HT488 to use STATIC IP mode, then use Option 02, 03, 04 to set up the HT488's IP, Subnet Mask, Gateway respectively. TFTP SERVER ADDRESS Follow Table 3 with voice menu option 06 to configure the IP address of the TFTP server. FIRMWARE SERVER IP ADDRESS Select voice menu option 13 to configure the IP address of the firmware server. CONFIGURATION SERVER IP ADDRESS Select voice menu option 14 to configure the IP address of the configuration server. UPGRADE PROTOCOL Select voice menu option 15 to choose firmware and configuration upgrade protocol. FIRMWARE UPGRADE MODE Select voice menu option 17 to choose firmware upgrade mode among the following three options: 1) always check, 2) check when pre/suffix changes, and 3) never upgrade Grandstream Networks, Inc. HT488 User Manual Firmware 1. 0. 3. 86 Page 17 of 31 Last Updated: 7/2007 CONFIGURING HT488 WITH WEB BROWSER HT488 ATA has an embedded Web server that will respond to HTTP GET/POST requests. It also has embedded HTML pages that allow users to configure the HT488 through a Web browser such as Microsoft's IE, AOL's Netscape or Mozilla Firefox installed on Windows or Unix OS. (Macintosh OS does not included). Access the Web Configuration Menu The HT488 HTML configuration page can be accessed via LAN or WAN ports. · FROM THE LAN PORT: 1. Type in "ipconfig /release", the IP address etc becomes 0 4. Type in "ipconfig /renew", the computer gets an IP address in 192. 168. 2. x segment by default 5. Open a web browser, type in the WAN side IP address ­ for example: http://HT503-WAN-IP-Address · Note: · · · WAN side HTTP access is disabled by default for security reason. You can enable HTTP access on the configuration page by setting "WAN side HTTP access" to be YES. Initial access to the configuration pages is always from the LAN port. The IVR announces 12 digits IP address, you need to strip out the leading "0" in the IP address. [. . . ] A parameter consists of a Capital letter P and 2 to 3 (Could be extended to 4 in the future) digit numeric numbers. i. e. , P2 is associated with "Admin Password" in the ADVANCED SETTINGS page. For a detailed parameter list, please refer to the corresponding firmware release configuration template. When Grandstream Device boots up or reboots, it will issue request for configuration file named "cfgxxxxxxxxxxxx", where "xxxxxxxxxxxx" is the MAC address of the device, i. e. , "cfg000b820102ab". [. . . ]