User manual GRASS VALLEY 8939FCA DATASHEET

[. . . ] 8939FCA/8939FCB Fiber Optic Mux/Demux Modules Key Features · Optical multiplexer/demultiplexer for combining signals on a single fiber · 8939FCA provides up to 8:1 or 1:8 multiplexing or demultiplexing using CWDM technology · Will accept a ninth 1310 nm signal for 9:1 multiplexing when connected to the EXP port of the 8939FCA · Using the 8939FCB connected to the EXP port of the 8939FCA, up to 16 channels can be transmitted on a single fiber · Up to 10 8939FCA modules can be housed in a GeckoFlex frame providing up to 80 channels of optical multiplexing or demultiplexing per 2 RU frame · The module is a passive optical device for reliable service 63 The 8939FCA and 8939FCB are bi-directional optical CWDM multiplexer/demultiplexer modules for the 2 RU GeckoFlex frame. [. . . ] GeckoFlex fiber-ready modules can be equipped with CWDM fiber transmitters for ultra-compact multiplexed optical capability. The 8939FCA can also be used with the 8935FCB module to increase the number of optical channels to 16 which can be transmitted over one single-mode fiber cable. Refer to the block diagrams shown on the following page for using the modules. Class |||a Laser Product 8939FCA COM CH8 1610 nm CH6 1570 nm CH4 1530 nm CH2 1490 nm EXP CH7 1590 nm CH5 1550 nm CH3 1510 nm CH1 1470 nm Class |||a Laser Product Applications · For transporting multiple SD/HD/3G-SDI video signal over a limited fiber cable capacity · When reducing infrastructure costs (cabling, electrical power consumption, space, etc. ) is required ­ multiplexed video over fiber gives us an 8:1 ratio on cabling and support equipment · Fiber is commonly used in any application where SD/HD/3G-SDI signals are found 8939FCB COM CH16 1450 nm CH14 1410 nm CH12 1370 nm CH10 1330 nm N/A CH15 1430 nm CH13 1390 nm CH11 1350 nm CH9 1310 nm Specifications Supported Frame Types GeckoFlex Ordering Information Environmental Storage temperature: -10 to +70°C Operating ambient temperature: -40 to +85°C These modules can be mounted in a GeckoFlex frame but not in other 8900 series frames, including Gecko-A or Gecko-V frames. These modules have no controls or settings. Power Rating 0. 0 Watts (passive) ­ single-slot one piece rear mount Reference Information The CWDM SFP transmitter submodule devices used on 8943CF and the SFP receiver used on 8943FC modules (or other fiber-ready GeckoFlex modules) used in conjunction with the 8939FCA and 8939FCB support the following frequencies supporting data rates up to 3 Gb/s: Model Transmitter Frequencies Supported Performance Specifications 8939FCA: 8-channel CWDM channels: 1470 nm, 1490 nm, 1510 nm, 1530 nm, 1550 nm, 1570 nm, 1590 nm, 1610 nm 8939FCB: 8-channel CWDM channels: 1310 nm, 1330 nm, 1350 nm, 1370 nm, 1390 nm, 1410 nm, 1430 nm, 1450 nm Expansion port wavelength coverage: 1260 nm > 1450 nm 8-channel insertion loss: 2. 25 dB max. Adjacent channel isolation: 35 dB typical Non-adjacent channel isolation: 50 dB min. Thermal stability: 0. 005 nm/°C Channel uniformity 8ch: 1. 25 dB typical 8939FCA Rear-mount fiber optic mux and demux 8:1 or 1:8 module with Ch1 ­ Ch8 with expansion port 8939FCB Rear-mount fiber optic mux and demux 8:1 or 1:8 module used with the 8939FCA to provide eight additonal fiber optic channels Ch9 ­ Ch16 SFP-CWDM3G-1-K SFP-CWDM3G-2-K SFP-CWDM3G-3-K SFP-CWDM3G-4-K SFP-CWDM3G-5-K SFP-CWDM3G-6-K SFP-CWDM3G-7-K SFP-CWDM3G-8-K SFP-13103G-M1DRX-K 1470 nm 1510 nm 1550 nm 1590 nm 1310 nm 1350 nm 1390 nm 1430 nm 1490 nm 1530 nm 1570 nm 1610 nm 1330 nm 1370 nm 1410 nm 1450 nm WARNING The COM and EXP outputs of the 8939FCA and 8939FCB may fall into the Class IIIa Laser Device catagory, depending on number of SFP input choices. Receiver Frequency Supported 1270 nm > 1610 nm Dual Receiver NOTE: The CWDM submodules listed above may also be used with the 8935CF and 8935FC but the 8935 modules only handle bit rates up to 1. 5 Gb/s. . For detailed specifications, installation, and setup instructions see: www. grassvalley. com/docs/modular 64 8939FCA/8939FCB Fiber Optic Mux/Demux Modules Block Diagrams for Mux/Demux Applications The 8939FCA module can be used alone for various applications or together with the 8939FCB module, depending on the application. In all of the applications using the 8939FCA and 8939FCB modules, the 8935CF/8935FC (1. 5 Gb/s) or 8943CF/8943FC (3 Gb/s) or other fiber-ready GeckoFlex modules feeding video to the 8939 modules must be fitted with the correct frequency SFP fiber optic submodule and cabled to the corresponding channel for that frequency. 8939FCA 9:1 Multiplexer to 1:9 Demultiplexer The 8939FCA can multiplex up to nine fiber video channels from two 8943CF (Coax to Fiber) modules and another 1310 nm Grass Valley fiber-ready module. [. . . ] This allows a total of 16 channels to be multiplexed and demultiplexed on a single fiber cable. COM COM Single-mode Fiber (up to 50 km) [. . . ]