User manual GTO PRO-SW 1000SERIES

[. . . ] Installation Manual for the ¨ + LIS TED 75 Series Automatic Gate Operator for Vehicular Swing Gates WARNING! READ ALL INSTRUCTIONS CAREFULLY AND COMPLETELY before attempting to install and use this automatic gate operator. Stay clear of the unit while it is operating and exercise caution at all times. , INC. 3121 Hartsfield Road · Tallahassee, Florida, USA 32303 Telephone (800) 543-GATE or (850) 575-0176 · Fax (850) 575-8912 · www. gtoinc. com © 2000 GTO, Inc. RB918 rev-04/22/02 This product meets and exceeds the requirements of UL 325, the standard which regulates gate operator safety, as established and made effective March 1, 2000, by Underwriters Laboratories Inc. GTO/PRO 1000 series automatic gate operators are intended for use with vehicular swing gates. These operators can be used in Class I, Class II and Class III applications. VEHICULAR GATE OPERATOR CLASS CATEGORIES Residential Vehicular Gate Operator-Class I: A vehicular gate operator (or system) intended for use in a home of one-to-four single family dwelling, or a garage or parking area associated therewith. [. . . ] NOTE: To change the DIP switch settings, you must turn the control box power switch OFF; move the switch; then turn the power back ON. PULL/PUSH: Set to PULL for swing gates that pull-to-open [factory setting]; PUSH for swing gates that push-to-open (see Push to Open Installation on pages 30-31). NOTE: The direction a gate opens is determined by standing inside the property and facing toward the gate. SNGL/DUAL: Set to SNGL for a single gate leaf [factory setting]; DUAL for dual gate leaves. See Setting the Control Board for Dual Gate Installations on page 39 for more information. See Setting the Control Board for Dual Gate Installations on page 39 for more information. S DIP switches OBSTRUCT SENS. PULL/PUSH SNGL/DUAL SEQ1 SEQ2 4 ON 1 2 3 MIN MAX LEARN AUTOC 60 STATUS LOSE + BATT ­ 120 OFF INERTIA MAX MIN UCT OBSTRS. SEN MAX USH PULL/P L UA SNGL/D EQ1 S SEQ2 MIN LEARN G RB OPN EDG CLS EDG OPN EDG CLS EDG ORG BLU GRN RED BLK ORG BLU GRN GRN ORG BLU WHT BLK RED SOLAR 18VAC ­ + ~ ~ SECO FIRST POWE R IN ND O TOR PERA ALAR M ACCE SSOR Y RCVR OPER ATOR 23 Potentiometers The three (3) potentiometers on the control board operate like a volume control on a radio. They control the auto close timer, inertia, and obstruction sensitivity of the operator. Use a small slotted screwdriver to turn the arrow in the center of the potentiometer. AUTO CLOSE (auto close timer): Determines how long the gate will remain open before it automatically closes. INERTIA: Fine tunes obstruction sensitivity in the opening and closing modes. INERTIA allows the operator to attempt to push an obstruction clear of the gate path. will attempt to push an obstruction briefly); when set to MAX, the operator will obstruct slowly (will attempt to push against an obstruct for a longer period). (obstruction sensitivity): Determines the amount of force exerted by the gate on an obstruction before the operator stops and reverses. When set to MAX, the operator will exert maximum gate force before obstructing (i. e. , the operator will require greater resistance before stopping and reversing. ). NOTE: Heavy gates and gates with high wind resistance may require the OBSTRUCT SENS. potentiometer to be set closer to MAX to prevent the operator from obstructing. Keep in mind, however, that while you must determine the best setting for smooth gate operation, you must ALSO determine the lowest possible setting for safe gate operation. ALWAYS KEEP SAFETY AT THE TOP OF YOUR LIST WHEN ADJUSTING OR SERVICING YOUR AUTOMATIC GATE OPERATOR! AUTOCLOSE 60 OFF 120 INERTIA MIN MAX OBSTRUCT SENS. PULL/PUSH SNGL/DUAL SEQ1 SEQ2 4 ON 1 2 3 MIN MAX LEARN B G R RCVR WARNING! All three potentiometers were set to minimum at the factory. potentiometer MUST be adjusted above the factory setting for your GTO/PRO 1000 series operator to function properly. If the potentiometer is left at MIN, your gate operator may "obstruct" (i. e. , stop and reverse) as soon as it is activated. [. . . ] Recommended for GTO/PRO 2000/2200, GTO/PRO SL-1000/SL-1200. Operator Solar Panel (FM122 ) - Improved Amorphous Silicon The 5 watt solar panel is a battery charger for use with GTO/PRO Low Voltage Automatic Gate Operator systems. Particularly suited for remote installations, the solar panel comes with tubular steel support, mounting clips, wire connectors, and 8 ft. Installation in some regions of the world will require multiple panels for adequate charging power. Recommended for GTO/PRO 1000, GTO/PRO 1200 and the GTO Bulldog Gate Lock. Dual gate installations require minimum of two (2) 5 watt solar panels for adequate charging power. Transformers for charging the gate operator battery RB566 ­ Standard 18 volt, 20 VA, AC transformer for GTO/PRO 1000 series gate operators with serial numbers. Bulldog Replacement Charger RB421 ­ Standard 12 volt DC charger (not shown) for maintaining battery included with the Bulldog Pedestrian Gate Lock. Replacement Batteries RB500 ­ The standard 12 volt, 7. 0 ampere-hour, maintenance-free battery for all GTO/PRO gate operators. [. . . ]