User manual HAIER 42EP24STV

[. . . ] PLASMA TV OWNER`S MANUAL MODELS: 42EP24STV Please read this manual carefully and completely before operating the unit, and retain this manual for future reference. WARNING RISK ELECTRIC SHOOK DO NOT OPEN WARNING : To reduce the risk of electric shock do not remove cover or back. No user-serviceable parts inside refer service to qualified service personnel. Safety of operators has been taken into consideration at the design and manufacture phase, but inappropriate operation may cause electric shock or fire. To prevent the product from being damaged, the following rules should be observed for the installation, use and maintenance of th product. The User Manual uses the following symbols to ensure a safe operation and prevent any damage to operators or properties: THIS SYMBOL INDICATES THAT HIGH VOLTAGE IS PRESENT INSIDE. [. . . ] (This feature can also be changed from the sound menu function screen) Personal: A spare setting that can be adjusted to personal tastes. Standard: Normal sound with moderate bass and treble setting. SOU. Mode Music Standard Theater Personal Music: Adjust the sound to best suit music programs. Theater: Enables extra bass and treble to enhance the movie experience. Picture Mode Press P. STD button on the remote controller for menu display, and then use CH+/- button to select the desired mode, press VOL+/- to confirm. (This change can also be made from Picture menu adjustment screen) PIC. Mode Vivid Standard Mild Custom Standard: normal mode. Custom: picture effect which you favorite. Sleep Timer Every press of SLEEP button, the timer will be set in the following sequence: Sleep 0Min Sleep 5Min Sleep 15Min Sleep 30Min Sleep 60Min Sleep 90Min Sleep 120Min Sleep 0Min If remaining time of set timer is to be displayed, press the SLEEP button once. Owner s Manual 17 System Menu This TV set has three methods to set channels, which are respectively Automatic search, manual search In this section, how to use the remote control to set channel is explained. fine tune. Channel Type Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the TV (i. e. , an antenna or a cable system). 1 Press MENU button and then use VOL+/- button to select the SYS. 2 Press CH+/- buttons to select "Channel Type" item. 3 Press VOL+ button to select Cable or Air item. When Air is selected, the TV will detect antenna signals and will search for antenna TV (NTSC and ATSC) channels available in your local area. When Cable is selected, the TV will detect cable company supplied signals and will search for cable TV (NTSC, ATSC, QAM modulated) channels available in your area. Make sure that registration with your cable TV provider and connection of equipment are completed. When Air and Cable are selected, the TV will detect the antenna signals and cable company supplied signals, and search for the antenna TV and cable TV channels available in your area. Color Sys. Switch A B C AUTO M/N 49. 75MHz Off Cable STD Note : the tuning menu will be only operated in normal TV mode. CATV Type 1 Press MENU button and then use VOL+/- button to select the SYS. 2 Press CH+/- buttons to select "CATV Type" item. 3 Press VOL+ button to select STD, IRC or HRC item. Note: STD, HRC and IRC identify various types of cable TV systems. Contact your local cable company to identify the type of cable system that exists in your particular area. Automatic Scan 1 Press MENU button and then use VOL+/- button to select the SYS. 2 Press CH+/- buttons to select "Auto Scan" item. 3 Press VOL+ button to ensure automatic search function work. 4 Press MENU button to stop automatic search function. After the search has finished, all channels now playing program will be automatically preset in order. Color Sys. Switch A B C AUTO M/N 49. 75MHz Off Cable STD 18 Plasma TV System Menu Fine Tune If the picture and/or sound are poor, try using the fine tune feature. Switch A B C 1 Repeat step 1-2, then press CH+/- buttons to select "Fine Tune" item. AUTO M/N 49. 75MHz Off Cable STD 2 Press VOL-/+ buttons repeatedly to carry out fine tune, till the best picture and sound are obtained, then loosen the button. Color System Usually this should be set in the auto position. However if the color displayed on the screen are incorrect, you can manually select the correct color system. Press MENU and then VOL+/- button, till the picture menu shown on the right will display on the screen. Press CH+/- buttons to select "Color Sys. ", then press the VOL-/+ buttons to select the correct color system. Switch A B C AUTO M/N 49. 75MHz Off Cable STD Skip After the programs are presetting, you can skip some programs so that to select your favorite channels only. Press CH+/- button or Direct-digit choosing button to select a channel directly. When you are satisfied with your choice, press MENU button to return to the previous menu or press EXIT button to return to TV viewing. If you want to recover the skipped channel 1. Use Direct-digit Choosing button to select the number of the channel to be recovered. [. . . ] 4:3 mode Choose 4:3 mode when you want to view a picture with an original 4:3 aspect ratio, with black bars appearing at both the left and right sides. Full screen( correspond with 16:9) Choose Full screen when you want to adjust the picture horizontally, in a linear proportion to fill the entire screen. one to one Choose one to one when you want to adjust the picture in real proportion, (Only available in PC signal, especial for 800X600 mode and modes of under it ) Vertical Zoom Choose Vertical Zoom when you want to adjust the picture the picture vertically, that is without any back bars. Half Zoom Choose Half Zoom when you want to enlarge the picture vertically by enlarge top of the picture, that is the letters on the bottom are still on the screen. [. . . ]