User manual HAIER 50FREE-3

[. . . ] Select spin program, but it does not work. The pulsator pauses during water inlet in wash and rinse. Explanation Balance the laundries to avoid slanting. The program is setting the drain time , certain period is needed before it starts spinning. It is to avoid splashing during water inlet Forbidden sign Contents marked with that symbol are actions forbidden to perform. Performing of those action may result in damage of the machine or influence the personal safety of the users. There may be some water flowing out of the drain hose in the first use of the machine. It is the water remained performance inspection by the factory. 16 1 Safety precautions Please insert the power cord into special receptacle with rated voltage. If the power cord is three-phase wire, please use three-phase receptacle. The earthing terminal of the receptacle must be earthed reliably. If it is two-phase wire, please guarantee that the earthing wire is earthed reliably. If possible , please adopt electric leakage protector. The power cord plug should be convenient to be pluged in or pluged out with hand while the washing machine runs normally. [. . . ] It is very important to your security and correct operating the machine. After switching on the power, the washing machine will set to common program including"wash, rinse, spin "automatically. To select other procedures, push the " WASH", " RINSE"or "SPIN"button to select the time of wash and spin, and the times of rinse. After switching on the power, if you push one of the button among "RINSE"and"SPIN the digitron of the former procedures will turn off automatically. If you push the "SPIN" button first, it will execute spin singly after starting. Install the inner cover 1. Open the top lid of the washing machine. 2. Put the inner cover component on the outer tub cover, aiming the inner cover shaft to the installation hole of the corresponding outer tub cover shaft groove. 3. Firstly insert the inner cover shaft of I side into the correspon -ding outer tub cover shaft groove, then push the another inner cover shaft into the corresponding outer tub cover shaft groove. Section · enlarging Please install to designated position to guarantee there are no dropping or abnormal sound in opening and closing of the inner cover, and the operation shall be smooth. Do not dismount the Push inner cover component after washing. Outer tub cover shaft groove Inner cover shaft Outer tub cover Inner cover Attention Even there's no water in the tub, a certain period is required before spin starting. Separate the laundries that are not colorfast from other laundries in washing. The pulsator will not rotate unless the water is filled to water level . After the machine starts operation, you can set the program and procedure during washing, set spinning time during rinsing but can not make setting in other cases. Install the bottom plate After you open the package, please lean the washing machine gently down on soft items ( like the towel cloth, blanket, etc. Install the bottom plate to the bottom of the machine with the eight screws by a cross screwdriver, then lift the machine up gently. 2. Do not trample or press the drain hose. 2 Push the PROGRAM SELECTION button to select the suitable automatic program PROGRAM After switching on the power, the machine will set to STANDARD program automatically. To select other program, push the PROGRAM SELECTION button till the corresponding indicator is on. For example: select SAVE WASH for the quick washing of QUICK wash Page11 the laundries with light dirt. 4. If extra drain hose is needed, please make separate purchase. The inner diameter of the extra hose shall not less than 26mm, and the length shall not exceed 1. 5m. 3 Push WASH RINSE suitable programs SPIN button to select POWER ON/OFF MIN START PAUSE If the drain hose is too long, cut it at mid point. To make smooth drainage, cut the front end of the hose slantingly. If the extra hose is too long, cut it either at A or at B point. 12 5 Install the water inlet hose Power On/Off button Wash remain time indicator digitron The program is selected but not on, It displays the total minutes of the program During operation of programs, it displays the remained time (minute). In case of abnormal phenomenon, it displays the abnormal symbol (see to Page 16) Page 16 1. Damage to the valves can result. Push the POWER ON/OFF button to switch on the power. If the START/PAUSE button is not pushed, the washing machine will automatically switch off the power after 5 minutes. Start/Pause button After the power is switched on, push it to Start the machine During working, push it to pause working. Connect the other ends to the water inlet valve . ( As figure 2) Figure 1 Jointer of the water inlet hose POWER ON/OFF Jointer of the water inlet valve Water absorption cushion Figure 2 START PAUSE WASH button Push the WASH buttonto set the wash procedure. During STANDARD GENTLE HEAVY programs, push theWASH button to set different wash time (STANDARD from0 to 25minutes GENTLE from 0 to 15 minutes;HEAVY from 30 to 50 minutes or 0 minutes ) During SAVE program, push the WASH button, the machine have no reaction. PROGRAM SELECTION button You can select from the following four programs. Program STANDARD HEAVY GENTLE SAVE Normal wash Large, thick or heavily soiled laundry Woollen textiles or underwear 10 min quick wash for load below 2 kg 6 11 4 Use the operation buttons A. [. . . ] For powder whitener, please dissolve it before use. The quantity of the laundries shall not exceed the rated value. The big laundries like the jeans shall be put in loosely. Standard usage quantity of the detergent and water quantity a. Please check if the laundries are applicable for washing. c. For laundries not waterabsorbing, please put them into water with hands. d. For laundries with much soil, please remove the soil first. You can add detergent on the part with serious soil directly. It is much easier to remove the soil by that mean. [. . . ]