User manual HAIER 50FREE-3B

[. . . ] Not wash The machine does not act Not spin The water level sensor is bad. Is the jointer of water inlet hose loose or awry? Drain hose Base Adjustable foot Adjustable foot film Fixed foot(3 pcs) Meaning and description of the symbols Warning sign There's abnormal sound inside the machine The water tap leaks Contents marked with that symbol are related to the safety of the product and the personal safety of the users. Please operate in strict conformity to the contents. Common phenomena Phenomena The spinning is intermittent when it starts. Select spin program, but it does not work. The pulsator pauses during water inlet in wash and rinse. Explanation Balance the laundries to avoid slanting. [. . . ] If the lint filter is lost or damaged, please contact costomer care agent of our company. Before washing, please check if the water tap is open , and if the water inlet pipe is connected properly. It is suggested to use low-foaming washing powder Dismantle Install 14 3 Installation and adjustment Please install and adjust the machine according to the requirement of the manual. It is very important to your security and correct operating the machine. Install the inner cover 1. Open the top lid of the washing machine. 2. Put the inner cover component on the outer tub cover, aiming the inner cover shaft to the installation hole of the corresponding outer tub cover shaft groove. 3. Firstly insert the inner cover shaft of one side into the corresponding outer tub cover shaft groove, then push the another inner cover shaft into the corresponding outer tub cover shaft groove. Please install to designated position to guarantee there are no dropping or abnormal sound in opening and closing of the inner cover, and the operation shall be smooth. Do not dismount the inner cover component after washing. Outer tub cover Outer tub cover shaft groove Inner cover shaft Inner cover component Left hand Right hand After switching on the power, the washing machine will set to common program including"wash, rinse, spin "automatically. To select other procedures, push the " WASH", " RINSE"or "SPIN"button to select the time of wash and spin, and the times of rinse. After switching on the power, if you push one of the button among "RINSE"and"SPIN the digitron of the former procedures will turn off automatically. If you push the "SPIN" button first, it will execute spin singly after starting. Attention Even there's no water in the tub, a certain period is required before spin starting. Separate the laundries that are not colorfast from other laundries in washing. The pulsator will not rotate unless the water is filled to water level . After the machine starts operation, you can set the program and procedure during washing, set spinning time during rinsing but can not make setting in other cases. Figure 1 Figure 2 Install the bottom plate After you open the package, please lean the washing machine gently down on softitems ( like the towel cloth, blanket, etc. 1. put the drain hose up to suitable position (Do not 2. Do not step on or press the drain hose. put it on ground. ) Notes: The highest point of drain pipe shuold be higher than the water level of washing tub for avoiding to siphon phenomenon during drain. 2 Push the PROGRAM SELECTION button to select the suitable automatic program PROGRAM After switching on the power, the machine will set to STANDARD program automatically. To select other program, push the PROGRAM SELECTION button till the corresponding indicator is on. For example: select SAVE WASH for the quick washing of QUICK wash Page11 the laundries with light dirt. 3 Push WASH RINSE suitable programs SPIN button to select 0. 7m<H<1. 2m POWER ON/OFF START PAUSE MIN 12 5 Install the water inlet hose Power On/Off button Wash remain time indicator digitron The program is selected but not on, It displays the total minutes of the program During operation of programs, it displays the remained time (minute). In case of abnormal phenomenon, it displays the abnormal symbol (see to Page 16) Page 16 1. Damage to the valves can result. Push the POWER ON/OFF button to switch on the power. If the START/PAUSE button is not pushed, the washing machine will automatically switch off the power after 5 minutes. Start/Pause button After the power is switched on, push it to Start the machine During working, push it to pause working. Connect the other ends to the water inlet valve . ( As figure 2) Figure 1 Jointer of the water inlet hose POWER ON/OFF Jointer of the water inlet valve Water absorption cushion Figure 2 START PAUSE WASH button Push the WASH buttonto set the wash procedure. During STANDARD GENTLE HEAVY programs, push theWASH button to set different wash time (STANDARD from0 to 25minutes GENTLE from 0 to 15 minutes;HEAVY from 30 to 50 minutes or 0 minutes ) During SAVE program, push the WASH button, the machine have no reaction. PROGRAM SELECTION button You can select from the following four programs. Program STANDARD HEAVY GENTLE SAVE Normal wash Large, thick or heavily soiled laundry Woollen textiles or underwear 10 min quick wash for load below 2 kg 6 11 4 Use the operation buttons A. [. . . ] Washing powder with poor quality or not used for a long period may get blocked. Please refer to the usage manual of the washing powder for the details. Standard usage quantity of the detergent and water quantity a. Please check if the laundries are applicable for washing. c. For laundries not waterabsorbing, please put them into water with hands. d. For laundries with much soil, please remove the soil first. You can add detergent on the part with serious soil directly. It is much easier to remove the soil by that mean. [. . . ]