User manual HAIER DW12-CBE5

[. . . ] - Appliances which are no longer being used must be made inoperable by cutting the power supply cord and removing the door lock. - If the supply cord is damaged, it must be replaced by the manufacture, its service agent of similarly qualified persons in order to avoid a hazard. - Fundamental rules to follow when using the appliance: * Never touch the dishwasher when barefoot or with wet hands or feet; * We discourage the use of extension cords and multiple sockets; * During installation, the power supply cord must not be excessively or dangerously bent or flattened; * If the appliance is not operating properly or maintenance must be performed, disconnect the appliance from the power supply. To maintain the EFFICIENCY and SAFETY of this appliance, we recommend: - call only the Service Centers authorized by the manufacturer. [. . . ] The additional cup rack can be swivelled in or out as required(see fig. C). . 5. GB Starting the Appliance Starting a wash cycle After having completed all of the installation steps in the preceding paragraphs, turn on the water to the unit, partially open the door of the dishwasher, and press the ON-OFF button "A" located on the control panel. At this point, the appliance is on and ready to be programmed. At the end of the wash cycle The end of the cycle will be indicated by six acoustical signal, at the same time the "F" indicator light will turn off. Open the door, turn off the appliance using the ON-OFF switch and turn off the water supply to the unit. Wait a few minutes before removing the dishes so as to avoid handling them while still hot (when they are more susceptible to breakage) and to get better drying results. Setting and Starting a wash Cycle Choose the desired cycle by pressing the cycle selection button "G". Each time it is pressed, one of the cycle indicator lights "F" will begin to blink in succession. Choose the wash cycle you feel is most appropriate for the type of dishes that need washing (consult the wash cycle table contained in this manual, especially when first using the appliance). Close the door and then the wash cycle has begun and cannot be modified. If necessary, read the paragraph entitled, "Cancelling or modifying a cycle while underway. "The end of the cycle will be signalled by six acoustic sound, and the indicator light "F" will turn off. Setting The Start Delay Time Open the door of the dishwasher partially. If the "J" button is pressed (see, Close-up View" Control Panel"). The start time for the wash cycle can be delayed for 2, 4, 6, 8, 10 or 12 hours. Each time the button is pressed, the "I" light will blink indicating the length of the delay. After selecting the delay time, the wash cycle can be set, as explained in "Starting a wash cycle. . . " , close the door and at this point the delay period will begin to count down. At the end of the delay time, the indicator will turn off and the cycle will start. Cancelling or modifying a cycle while underway Premise: A cycle that is underway can only be modified if it has only been running for a short time. Otherwise, the detergent may have already been used, and the appliance may have already drained the wash water. If this is the case, the detergent dispenser must be refilled (see the paragraph entitled, "Loading the Detergent"). NOTE: a) During the delay period, none of the settings can be modified. If necessary, they can be cancelled by pressing press the ONOFF button "A" located on the control panel. b) If the door is opened during the delay period, the clock will stop the countdown. -Use the right amount of detergent: if you use too much detergent, the result will not be cleaner dishes, but, rather, a greater negative impact on the environment. How to keep Your Dishwasher in Shape After Every Wash After every wash, turn off the water supply to the appliance and leave the door slightly ajar so that moisture and odors are not trapped inside. When You Go on Holiday When you go on holiday, it is recommended that you run a wash cycle with the dishwasher empty and then remove the plug from the socket, turn off the water supply and leave the door of the appliance slightly ajar. This will help the seals last longer and prevent odors from forming within the appliance. Remove the plug Before cleaning or performing maintenance, always remove the plug from the socket. Do not run risks. Moving the Appliance If the appliance must be moved, try to keep it in a vertical position. If absolutely necessary, it can be positioned on its back. No solvents or Abrasive Cleaning Products To clean the exterior and rubber parts of the dishwasher, do not use solvents or abrasive cleaning products. [. . . ] If the appliance is level, it will help ensure proper performance. Cold Water Connection Connect the cold water supply hose to a threaded 3/4(gas) connector, inserting the small filter supplied with the dishwasher and making sure that it is fastened tightly in place (see Fig. 1). If the water pipes are new or have not been used for an extended period of time, let the water run to make sure that the water is clear and free of impurities. If this precaution is not taken, there is a risk that the water inlet can get blocked and damage the appliance. fig. 1 Drain Hose Connection Insert the drain hose into a drain pipe with a minimum diameter of 4cm, or let it run into the sink, making sure to avoid bending or crimping it. Use the special plastic support that comes with the appliance (see Fig. 2). [. . . ]