User manual HAIER DW12-EFMS

[. . . ] - The carpet must not obstruct the opening when the appliance is installed on a carpeted floor. If the supply cord is damaged, it must be replaced by the manufacture, its service agent of similarly qualified persons in order to avoid a hazard. or feet; * We discourage the use of extension cords and multiple sockets; * During installation, the power supply cord must not be excessively or dangerously bent or flattened; Close-up View (control panel) A B C E A B C ON-OFF Light Program Symbols Cycle Select Knob D D E Handle For Opening Door ON-OFF Button . 1. GB Close-up View (Interior) A B C H G D E F A B C D Upper Rack Rack Height Adjuster Top Spray Arm Lower Rack E F G H Bottom Spray Arm Washing Filter Detergent and Rinse Aid Dispenser Salt Container Cap Technical characteristics Width Depth Height Capacity Mains water pressure Power voltage Total absorber power 60 cm 60 cm 85 cm 12 standard place settings 0. 03-0. 6 MPa 220V-240V~ 50Hz 2100W GB . 2. Salt Salt The hardness of the water varies from place to place. If hard water is used in the dishwasher, deposits will form on the dishes and utensils. The appliance is equipped with a special softener that uses a salt specifically designed to eliminate lime and minerals from the water. [. . . ] A) so that only one section may be used when the silverware load is light. - Silverware should be placed in the silverware basket with the handles at the bottom; if the rack has side baskets, the spoons should be located individually into the appropriate slots. Especially long utensils should be placed in the horizontal position at the front of the upper rack. How to Use the Upper Rack The upper rack is designed to hold more delicate and lighter dishware, such as glasses, coffee and tea cups and saucers, as well as plates, small bowls and shallow pans (as long as they are not too dirty). The upper rack can be adjusted for height by using the knobs located on both sides of the rack itself (see fig. B). Position the dishes and cookware so that they are not moved by the spray of water. Load for 12 Standard Settings 1 2 3 4 Fig. A Fig. B . 5. GB Turning on the Appliance Starting a wash cycle - Make sure that the plug of the appliance is inserted into the wall socket. - Load the dishwasher (see the section "Loading the Dishwasher"). - Pour in the detergent (see the section "Salt, Detergent and Rinse Aid"). - Turn the knob located on the right of the control panel clock wise to the desired cycle number or symbol (see the section "Wash Cycle Table"). If you forget to load some of dishes The wash cycle can be interrupted by pressing the ON-OFF button. At the end of the wash cycle When the knob stops turning and is aligned with the STOP mark (see figure), the cycle has finished. Turn off the appliance using the ON-OFF button, turn off the water supply and open the door of the dishwasher. Wait a few minutes before unloading the dishwasher to avoid handling the dishes and utensils while they are still hot and more susceptible to breakage. Cancelling or modifying a wash cycle setting Premise: A cycle that is underway can only be modified if it has been running for a short time. Otherwise, the detergent may have already been used, and the appliance may have already drained the wash water. If this is the case, the detergent dispenser must be refilled (see paragraph "Loading the detergent"). Rotate the knob clockwise to the desired cycle setting (see the section "Starting a wash cycle"). Then, turn the dishwasher back on using the ON-OFF button. GB . 6. Energy Saving Tips - It is important to try and run the dishwasher when it is fully loaded - Use the right amount of detergent: if you use too much detergent, in order to save on energy. In order to prevent odours from form the result will not be cleaner dishes, but, rather, a greater nega ing and food from caking onto the dishes, you can run the soak tive impact on the environment. - There is no utility in rinsing dishes, cookware and utensils be - Choose the right wash cycle: the choice depends on the type of fore placing them in the dishwasher. dishware, cookware and utensils being washed and how dirty they are. How to Keep Your Dishwasher in Shape After Every Wash After every wash, turn off the water supply to the appliance and leave the door slightly ajar so that moisture and odours are not trapped inside. Moving the Appliance If the appliance must be moved, try to keep it in the vertical position. Seals Remove the Plug Before cleaning or performing maintenance, always remove the plug from the socket. [. . . ] Attention: The special plastic hose support must be solidly fastened to the wall to prevent the drain hose from moving and allowing water to spill outside the drain. Electrical Connection After making sure that the voltage and frequency values for the current in the home correspond to those on the rating plate (located on the stainless steel inner door of the appliance) and that the electrical system is sized for the maximum voltage on the rating plate, insert the plug into an electrical socket which is earthed properly (the earthing of the appliance is a safety requirement mandated by law). If the electrical socket to which the appliance must be connected is not appropriate for the plug, replace the plug rather than using adaptors or the like as they could cause overheating and burns. fig. 1 fig. 2 Drain Hose Connection Insert the drain hose into a drain pipe with a minimum diameter of 4cm, or let it run into the sink, making sure to avoid bending or crimping it. [. . . ]