User manual HAIER DW9-AFE

[. . . ] - The appliance is not intended for use by young children or inform persons without supervision. - Young children should be supervised to ensure that they do not play with the appliance. - Keep detergents out of the reach of children, who must also be kept away from the dishwasher when it is open. - This appliance cannot be installed outdoors, not even if the area in which it is installed is covered by a roof; it is also very dangerous to leave it exposed to the rain and elements. [. . . ] Especially long utensils should be placed in the horizontal position at the front of the upper rack. How to Use the Upper Rack The upper rack is designed to hold more delicate and lighter dishware, such as glasses, coffee and tea cups and saucers, as well as plates, small bowls and shallow pans (as long as they are not too dirty). Position the dishes and cookware so that they do not get moved by the spray of water. (See fig. B) Lower Rack Upper Rack Load for 9 Standard Settings 1 2 3 4 fig. A fig. B . 5. GB Turning on the Appliance Starting a wash cycle After having completed all of the installation steps in the previousparagraphs, turn on the water all the way and press the ON/OFF button (D) located on the control panel. At this point, the appliance is on but you must wait a few seconds before programming the cycle setting. Setting the Wash Cycle with a Delayed Start Time By pressing "F" button (see close-up view-'Control panel") the start of wash cycle may be delayed 1 to 12 hours. Each time the button is pressed, the display (G) will show the number of hours for the delay period. After selecting the wash cycle, a short acoustic signal will sound and after a few seconds, the delay time on the display will blink indicating that the countdown has begun. Setting and Starting a wash Cycle Select the desired cycle by pressing the selector button (I). Each time the button is pressed, one of the "J" cycle indicator lights will come on in succession. Choose the wash cycle you feel is most appropriate for the type of dishes that need washing (consult the wash cycle table contained in this manual, especially when first After the time has elapsed, the cycle will start. using the appliance). After a few seconds, the wash cycle has beNOTE: gun and can no longer be changed. During the delay period, it is preferable not to change any of the settings, If this is necessary, all of the settings must be cancelled by pressing the ON/OFF button (D). At this point, all of the steps for "setting the wash cycle with a Delayed Start Time" and "Setting and Starting a wash cycle" must be repeated, following the instructions contained in the corresponding sections. If the door of the appliance is opened during the delay period, the countdown will stop. The display will show the remaining time. Cancelling or modifying a cycle while it is underway Premise : A cycle that is underway can only be modified if it has only been running for a short time only. Otherwise, the detergent may have already been used, and the appliance may have already drained the wash water. If this is the case, the detergent dispenser must be refilled (see the paragraph entitled, "Loading the Detergent"). To modify a cycle that is already underway, press the ON/OFF button (D), all of the settings will be cancelled. To set a new cycle, follow the instructions contained in the paragraph entitled "Setting and starting a wash cycle". Wash Cycle Program Light The dishwasher is equipped with a LED indicator light (J) 1/2 load Button that blinks when the wash cycle indicated by the light itself is activated. This button (see "close-up View - Control Panel", letter"E") alAt the end of the wash cycle An acoustic signal will sound six times, indicating that the wash cycle has finished, and the cycle indicator light (J) for the cycle will go out. Wait a few minutes before unloading the dishwasher to avoid handling the dishes and utensils while they are still hot and more susceptible to breakage. They will also dry better. lows washing dishes using the upper rack only if there are not enough dishes for a full load. It can be used before setting any of the wash cycle, except for the intensive cycle ( if included in the wash cycle table). [. . . ] If the water pipes are new or have not been used for an extended period of time, let the water run to make sure that the water is clear and free of impurities. If this precaution is not taken, there is a risk that the water inlet can get blocked and damage the appliance. Hot Water Connection The water supply to the appliance can also be connected to the house's hot water line (centralised system, heating system), as long as it does not exceed a temperature of 60 . In this case, the wash cycle time will be shortened by about 15 minutes and the wash efficiency slightly reduced. Fig. 1 Installation Drain Hose Connection Insert the drain hose into a drain pipe with a minimum diameter of 4cm, or let it run into the sink, making sure to avoid bending or crimping it. Use the special plastic support that comes with the appliance (see Fig. 2). [. . . ]