User manual HAIER DW9-CBE

[. . . ] The dishwasher must not be connected to the electricity supply while installation is being carried out. The mains electricity supply must conform to the details shown on the dishwasher rating plate. Do not connect the dishwasher to the electricity supply using an extension cable. After the appliance has been installed, the mains plug should still be easily accessible. [. . . ] The dispenser must be refilled before the start of each wash cycle following the instructions provided in the "Programme overview". 4 5 Adding detergent To open cover "4" on the dispenser, press button "5". The detergent for the wash cycle should be poured into compartment"6". The detergent for the pre-wash cycle should be poured into compartment"7". After the detergent has been placed in the dispenser, close the cover and press down until it clicks into place. 7 6 Notice: To facilitate closing the cover, remove any excess detergent on the edges of the dispenser. 9 Not suitable for the dishwasher What you should not put into the dishwasher en Cutlery and tableware manufactured in whole or part from wood. Furthermore, the adhesives that are used are not suitable for the temperature inside the dishwasher. Delicate decorative glassware and vases, special antique or irreplaceable china. Plastic objects that are not resistant to hot water, copper and pewter utensils are also not suitable. Items with decorative patterns printed or painted onto the surface of crockery, glasses, etc. Aluminium and silver items tend to become discoloured or faded if washed in the dishwasher. Some types of glass can become opaque in appearance after they have been washed many times in a dishwasher. To cancel the time delay setting, press the Delayed Start button until the delayed start indicator "E" goes out. Rotate programme dial "J" to select the desired programme. A CE H B DF G I J 16 en After 3 seconds the delayed start indicator "E" blinks. The programme will start when both lights fade. Cancelling or modifying a cycle A cycle that is underway can be modified if it has only been running for a short time. Otherwise, the detergent may have already been used and the appliance may have already drained the wash water. If this is the case, the detergent dispenser must be refilled (see the paragraph entitled, "Adding Detergent"). To modify a cycle that is already underway, follow the instructions contained in the paragraph entitled "Reset function" and select the programme you require (see the paragraph entitled "Switching the dishwasher ON"). A CE H B DF G I 3in1 function When using "3 in 1" combination products, the rinse-aid and salt indicator lights are no longer relevant. It may be helpful to select the lowest possible setting for water hardness. If you decide to switch to using a standard detergent system we advise you to: 1: Refill both the salt and rinse aid compartments. 2: Switch the water hardness setting to the highest possible position and run for three normal cycles with the appliance left empty. 3: Readjust the water hardness setting again according to the conditions for your region. Warning Do not place the tablets in the cutlery basket as this will result in poorer wash results. The tablets should be placed in the detergent doser. Notice: 3 in 1 or similar tablets should not be used when Heat Wash, Rapid wash or Soak programmes are selected. Reset drain function You can use the "Reset" function to stop the wash cycle when running by rotating the dial to "Reset". [. . . ] The model type number (Mod. . . ) and the serial number (S/N. . . ), which is shown on the plate on the inner part of the door. Lower spray arm rotates with difficulty. Spray arm is blocked by small items or food residue. Detergent compartment lid cannot be closed Detergent compartment has been overfilled. Mechanism is clogged with remnants of detergent. Remnants of detergent stuck inside dispenser. Compartment was damp when it was filled up with detergent. Compartment must be dry before detergent is added. 22 en Water remains inside appliance after programme has ended. Blockage or kink in drainage hose. Wait for the programme to end. . . . during washing Unusual amount of foam is created Normal washing up liquid has been poured into the rinse-aid container. [. . . ]