User manual HAIER HSU-12HF03(B)

[. . . ] Inadequate repairs may result in a major source of danger for the user of the air conditioner. Do not damage any parts of the air conditioner that carry refrigerant by piercing or perforating the air conditioner's tubes with sharp or pointed items, crushing or twisting any tubes, or scraping the coatings off the surfaces. If the refrigerant spurts out and gets into eyes, it may result in serious eye injuries. Do not obstruct or cover the ventilation grille of the air conditoner. Do not put fingers or any other things into the inlet/outlet and swing louver. [. . . ] The distance between the indoor unit and the floor should be more than 2m. The appliance is not intended to use by young children or infirm persons without supervision. 9. Young children should be supervised ensure that they do not play with the appliance. 11 . The wiring diagram is attached inside the machine. Air Conditioner Edition:2006/01/09 Parts and Functions Indoor Unit Inlet grille Test running switch(manual) Used only for test running in cooling o when room temp. Don't use it in normal operation. Emergency switch(manual) Used when remote controller is lost or defective. Unit will run temporarily. Remote signal receiver Air filter Vertical flap Use remote controller to adjust up and down air flow. (Don't adjust it manually. ) A beeping sound is generated when a signal from remote controller is received. Power indicator Lights up when unit starts. Timer mode indicator Lights up when Timer operation is selected. Operation mode indicator Lights up during compressor running. Actual inlet grille may vary from the one shown in the manual according to the product purchased. Outdoor Unit HSU-09C13 HSU-12HF03(B) HSU-18C13 HSU-22C13 HSU-24C13 OUTLET INLET CONNECTING PIPING AND ELECTRICAL WIRING DRAIN HOSE Air Conditioner Edition:2006/01/09 Parts and Functions Operation Buttons and display of the remote controller. 1. MODE Used to select AUTO run, COOL, DRY, HEAT and FAN operation 1 2 3 4 ON/OFF TEMP 5 6 7 8 9 10 AUTO LO MED HI 11 18 MODE SET Used for unit start and stop. 12 FAN TIMER 19 13. FAN 20 Used to select fan speed LO, MED, HI, AUTO 13 14 15 SLEEP SWING CLOCK 14. RESET Used to reset the controller back to normal condition. When unit is started for the first time and after replacing batteries in remote controller, clock should be adjusted as follows: Press CLOCK button, "AM" or "PM" flashes. After time setting is confirmed, press SET, "AM "and "PM" stop flashing, while clock starts working. setting, unit will run in mild DRY mode. Hints On cooling only unit, heating mode is not available. When starting it next time, just press ON/OFF button and unit will run in previous status. Air Conditioner Edition:2006/01/09 Operation (5) Air flow direction adjustment After operation mode is selected, vertical flap will open automatically according to the mode. COOL About 10o Up and down (Use remote controller) Left and right air flow adjustment Press SWING button, vertical flap will move within (manual) the range shown in the Fig. Move the horizontal blade by a knob on air conditioner to adjust left and right direction referring to Fig. About 10o COOL About 45o HEAT About 60o Cautions: It is advisable not to keep vertical flap at downward position for a long time in COOL or DRY mode, otherwise, condensate water might occur. Cautions: When humidity is high, condensate water might occur at air outlet if all horizontal louvers are adjusted to left or right. (6) Unit stop Press ON/OFF button. Vertical flap closes automatically. Cautions: Unit won't restart until 3 minutes have elapsed, due to system protection. HEAT mode is not available on cooling only unit. Hints As cold air flows downward in COOL mode, adjusting air flow horizontally will be much more helpful for a better air circulation. As warm air flows upward in HEAT mode, adjusting air flow downward will be much more helpful for a better air circulation. (2) Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as follows: ON TIMER ON OFF TIMER OFF ON OFF blank TIMER ON-OFF Select TIMER ON-OFF. "ON" will flash. (3)Time setting for TIMER ON Press HOUR button. Every time the button is pressed, time increases 10 min. AM refers to morning and PM to afternoon ON/OFF TEMP MODE 1 3 SET 6 TIMER FAN 5 SWING 2 4 CLOCK SLEEP (4) Time confirming for TIMER ON After time setting, press TIMER button to confirm. Time displayed: Unit starts at x hour x min. LOCK RESET (5)Time setting for TIMER OFF Follow the same procedures in "Time setting for TIMER ON". (6) Time confirming for TIMER OFF After time setting, press SET button to confirm, "OFF" stops flashing Time displayed: Unit stops at X hour X min. To cancel TIMER mode Just press TIMER button several times until TIMER mode disappears. Air Conditioner Edition:2006/01/09 Operation Emergency operation and test operation Emergency Operation: Carry out this operation only when the remote controller is defective or lost. [. . . ] When the remote controller is manipulated for the removal, then the selected operation by the remote controller. Air Conditioner Edition:2006/01/09 Operation Comfortable SLEEP Before going to bed at night, you can simply press the SLEEP button and unit will bring you a sound sleep in selected mode. In COOL mode One hour after SLEEP mode starts, temp. won't be too low for your sleep. (As shown in Fig. l) o o ON/OFF TEMP MODE SET FAN TIMER SWING CLOCK SLEEP LOCK RESET In HEAT mode One hour after SLEEP mode starts, temp. (As shown in Fig . 2) SLEEP operation starts SLEEP operation stops Approx. setting Unit stop Power Failure Resume Function If the unit is started for the first time, the compressor will not start running unless 3 minutes have elapsed. [. . . ]