User manual HAIER HSU-12HSB03/R2

[. . . ] SPLIT TYPE ROOM AIR CONDITIONER OPERATION MANUAL HSU-07RS03/R2 HSU-09RS03/R2 HSU-12RS03/R2 HSU-18RS03/R2 HSU-22RS03/R2 H2SM-18HS03/R2 HSU-09HS03/R2(DB) HSU-12HS03/R2(DB) HSU-18HS03/R2(DB) HSU-22HS03/R2(DB) HSU-12HSB03/R2(DB) Please read this operation manual before using the air conditioner. No. Cautions Disposal of the old air conditioner Before disposing an old air conditioner that goes out of use, please make sure it's inoperative and safe. Unplug the air conditioner in order to avoid the risk of child entrapment. It must be noticed that air conditioner system contains refrigerants, which require specialized waste disposal. [. . . ] button Every time the button is pressed, temp. setting increase 1 C, if kept depressed, it will increase rapidly Every time the button is pressed, temp. setting increase 1 C, if kept depressed, it will decrease rapidly Select a desired temperature. 4. Fan speed selection Press FAN button. For each press, fan speed changes as follows: Remote controller: LOW MED HI AUTO Air conditioner is running under displayed fan speed When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature. 5. Unit stop Press ON/OFF button, the unit stops. 10 Operation Dry Operation 1. The liquid crystal will display the working state of last time (Except Timer, Sleep, Power/Soft and Health airflow). Remote controller 2. Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select DRY operation 3. Select temp. setting Press TEMP. button Every time the button is pressed, temp. setting increase 1 C, if kept depressed, it will increase rapidly Every time the button is pressed, temp. setting increase 1 C, if kept depressed, it will decrease rapidly Select a desired temperature. 4. Fan speed selection Press FAN button. For each press, fan speed changes as follows: Remote controller: LOW MED HI AUTO COOL operation starts when room temp. is higher than temp. setting. Ultra-low air flow Air conditioner is running under displayed fan speed In DRY mode, when room temperature becomes 2oC higher than temp. setting, unit will run intermittently at LOW speed regardless of FAN setting. Temp. setting+2oC Temp. setting On reaching temp. setting +2oC unit will run in mild DRY mode. 5. Unit stop Press ON/OFF button, the unit stops. 11 Operation Fan Operation Remote controller 1. The liquid crystal will display the working state of last time (Except Timer, Sleep, Power/Soft and Health airflow). 2. Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select FAN operation 3. Fan speed selection Press FAN button. For each press, fan speed changes as follows: Remote controller: LOW MED HI 4. Unit stop Press ON/OFF button, the unit stops. About FAN operation In FAN operation mode, the unit will not operate in COOL or HEAT mode but only in FAN mode , AUTO is not available in FAN mode. And temp. setting is disabled. In FAN mode, SLEEP operation is not available. 12 Operation Heat Operation Remote controller 1. The liquid crystal will display the working state of last time (Except Timer, Sleep, Power/Soft and Health airflow). 2. Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select HEAT operation 3. Select temp. setting Press TEMP. button Every time the button is pressed, temp. setting increase 1 C, if kept depressed, it will increase rapidly Every time the button is pressed, temp. setting increase 1 C, if kept depressed, it will decrease rapidly Select a desired temperature. 4. Fan speed selection Press FAN button. For each press, fan speed changes as follows: Remote controller: LOW MED HI AUTO Air conditioner is running under displayed fan speed IN HEAT mode, warm air will blow out after a short period of the time due to cold-draft prevention function. When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature. 5. Unit stop Press ON/OFF button, the unit stops. 13 Operation Air Flow Direction Adjustment 1. Status display of air sending direction Vertical flap Pos. 1 Pos. 1 Pos. 2 Pos. 3 Pos. 4 Pos. 5 Pos. 6 Pos. 2 Pos. 3 Pos. 4 Pos. 5 Horizontal louvers (Auto swing) Pos. 6 Pos. 7 Pos. 8 2. Up and down air flow direction For each press of button, air flow direction on remote controller displays as follows according to different operation modes: COOL/DRY/FAN: Pos. 1 Pos. 2 Pos. 3 Pos. 4 Pos. 6 remote controller: HEAT: remote controller: AUTO: remote controller: Pos. 5 Pos. 4 Pos. 3 Pos. 2 Pos. 1 Pos. 6 Pos. 1 Pos. 2 Pos. 3 Pos. 4 Pos. 5 Pos. 6 The vertical flap will swing according to the above positions 3. Left and right air flow direction For each press of remote controller: Pos. 1 Pos. 2 Pos. 3 button, remote controller displays as follows : Pos. 4 Pos. 5 Pos. 6 Pos. 7 Pos. 8 The horizontal louvers will swing according to the above positions. Note:When restart after remote turning off, the remote controller will automatically memorize the previous set swing position. 14 Operation Sleep Operation Before going to bed, you can simply press the SLEEP button and unit will operate in SLEEP mode and bring you a sound sleep. Use of SLEEP function After the unit starts, set the operation status, then press SLEEP button before which the clock must be adjusted and time being set. setting so that room temperature won't be too Iow for your sleep. SLEEP operation starts SLEEP operation stops Approx. 6hrs Rises 1OC 1 hr 1 hr Rises 1OC Temp. setting Unit stop In COOL, DRY mode Remote Controller 2. In HEAT mode 1 hours after SLEEP mode starts, temp will become 2 OC lower than temp. setting so that room temperature won't be too high for your sleep. Temp. setting 1 hr Decreases 2OC 1 hr Decreases 2OC 3 hrs 3 hrs SLEEP operation starts Rises 1OC Unit stop SLEEP operation stops In HEAT mode 3. In AUTO mode The unit operates in corresponding sleep mode adapted to the automatically selected operation mode. [. . . ] 5. Select the appropriate fan direction according to the actual conditions. 19 Operation Emergency and Test Operation Emergency operation: Use this operation only when the remote controller is defective or lost. When the emergency operation switch is pressed, the" Pi "sound is heard once, which means the start of this operation. In this operation, the system automatically selects the operation modes, cooling or heating, according to the room temperature. When machine is running in emergency, the set value of temperature and wind speed couldn't be altered; meanwhile, it can't operate for dehumidifying or under timing mode. Test operation: Test operation switch is the same as emergency switch. [. . . ]