Detailed instructions for use are in the User's Guide.
[. . . ] SPLIT TYPE ROOM AIR CONDITIONER
OPERATION MANUAL
HSU-09LR03 HSU-12LR03 HSU-12LRA03 HSU-18LRA03
Please read this operation manual before using the air conditioner
No. 0010562975
Cautions
Disposal of the old air conditioner
Before disposing an old air conditioner that goes out of use, please make sure it's inoperative and safe. Unplug the air conditioner in order to avoid the risk of child entrapment. It must be noticed that air conditioner system contains refrigerants, which require specialized waste disposal. The valuable materials contained in an air conditioner can be recycled . Contact your local waste disposal center for proper disposal of an old air conditioner and contact your local authority or your dealer if you have any question. [. . . ] When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature.
5. Unit stop
Press ON/OFF button, the unit stops.
10
Operation
Display board
1. Unit start
Dry Operation
Remote controller
Press ON/OFF on the remote controller, unit starts.
2. Select operation mode
Press MODE button. For each press, operation mode changes as follows: Remote controller:
AUTO COOL DRY FAN
Then Select DRY operation
PURIFY
3. Select temp. setting
FRESH
POWER/SOFT
Press TEMP. button Every time the button is pressed, temp. setting increase 1oC, if kept depressed, it will increase rapidly. Every time the button is pressed, temp. setting decrease 1oC, if kept depressed, it will decrease rapidly. Select a desired temperature.
4. Fan speed selection
Press FAN button. For each press, fan speed changes as follows: Remote controller:
LOW MED HI AUTO
Air conditioner is running under displayed fan speed. In DRY mode, when room temperature becomes lower than temp. setting+2oC, unit will run intermittently at LOW speed regardless of FAN setting.
5. Unit stop
Press ON/OFF button, the unit stops.
11
Operation
Display board
Fan Operation
Remote controller
1. Unit start
Press ON/OFF on the remote controller, unit starts.
2. Select operation mode
Press MODE button. For each press, operation mode changes as follows: Remote controller:
AUTO COOL DRY FAN
Then Select FAN operation
PURIFY
3. Fan speed selection
FRESH
Press FAN button. For each press, fan speed changes as follows: Remote controller:
POWER/SOFT
LOW
MED
HI
4. Unit stop
Press ON/OFF button, the unit stops.
About FAN operation
In FAN operation mode, the unit will not operate in COOL mode but only in FAN mode , AUTO is not available in FAN mode. And temp. setting is disabled. In FAN mode, SLEEP and POWER/SOFT operation is not available.
12
Operation
Air Flow Direction Adjustment
1. Status display of air sending
Vertical flap
Pos. 1 Pos. 1 Pos. 2
PURIFY
Horizontal louvers
Pos. 2 Pos. 3 Pos. 4 Pos. 5
Pos. 3
FRESH
Pos. 4
POWER/SOFT
Pos. 5 Pos. 6
(Auto swing)
Pos. 6 Pos. 7 Pos. 8
2. Up and down air flow direction
For each press of button, air flow direction on remote controller displays as follows according to different operation modes: COOL/DRY/FAN remote controller: : AUTO: remote controller:
Pos. 1 Pos. 2 Pos. 3 Pos. 4 Pos. 6
Pos. 1
Pos. 2
Pos. 3
Pos. 4
Pos. 5
Pos. 6
The vertical flap will swing according to the above positions
3. Left and right air flow direction
For each press of remote controller:
Pos. 1 Pos. 2 Pos. 3
button, remote controller displays as follows :
Pos. 4 Pos. 5 Pos. 6 Pos. 7 Pos. 8
The horizontal louvers will swing according to the above positions.
The units of HSU-09LR03 and HSU-12LR03 have no SWING LEFT/RIGHT function.
Note:When restart after remote turning off, the remote controller will automatically memorize the previous set swing position. 13
Operation
Display board
Sleep Operation
Before going to bed, you can simply press the SLEEP button and unit will operate in SLEEP mode and bring you a sound sleep. Use of SLEEP function After the unit starts, set the operation status, then press SLEEP button before which the clock must be adjusted and time being set. setting so that room temperature won't be too Iow for your sleep.
SLEEP operation starts
SLEEP operation stops Approx. 6hrs Rises 1OC
1 hr
1 hr
Rises 1OC
Temp. setting
Unit stop
In COOL, DRY mode
Remote Controller
PURIFY
2. In AUTO mode The unit operates in corresponding sleep mode adapted to the automatically selected operation mode. 4. Set the wind speed change when sleeping If the wind speed is high or middle before setting for the sleep, set for lowing the wind speed after sleeping. 5. Note to the power failure resume: press the sleep button ten times in five seconds and enter this function after hearing four sounds. And press the sleep button ten times within five seconds and leave this function after hearing two sounds.
NOTE: With the power failure resume, when setting the TIMER ON, TIMER OFF and TIMER ON/OFF, it's memorized as shutdown status when resuming after power out.
FRESH
POWER/SOFT
14
Operation
Display board
Timer On/Off Operation
Remote Controller
Set clock correctly before starting TIMER operation. After unit starts, select your desired operation mode Operation mode will be displayed on LCD. Every time the button is pressed, display changes as follows: Remote controller:
BLANK
TIMER ON TIMER OFF TIMER ON-OFF
Then select your desired TIMER mode (TIMER ON or TIMER OFF). " "or " "will flash.
3. Time setting
Press HOUR button. [. . . ] inlet grill's top plate
2. Detach the standard air filter
Push up the filter's center tab slightly until it is released from the stopper, and remove the filter downward.
AIP(air ionization purify)
(bottom frame)
3. Take the VC layer + Bacteria-killing medium sets
Take out Take the VC layer or the Bacteria-killing medium sets from the filter. Push the bottom frame of AIP layer, and push up the handle at the same time in order take out the AIP layer board in turns.
(AIP board)
****
Note:the green aspect of the bacteria-killing medium air purifying filter will face outside, the white aspect will face to the machine. The yellow aspect of the VC layer will face outside, the white aspect will face to the machine.
4. The installation of AIP layer, VC layer + Bacteria-killing medium sets (must be installed)
5. Close the Inlet Grille
Put down the inlet grill's top plate, and close the inlet grill.
Common sense:
In order to keep the AIP layer having a highly work effect , it should be cleaned regularly or aperiodically just according to the working environment. [. . . ]