User manual HARMAN KARDON AVR 20

[. . . ] DIRECT INPUT CENTER é ANTENNA MULTI OUT TV MONI CENTER 8OHMS MAIN IN PRE OUT L FRONT R SUB WOOFER LD DIGITAL IN ° ¬ î SWITCHED UNSWITCHED AC OUTLETS 230V 50/60Hz) OUT VCR2 OUT VCR2 IN å ç © AM GND OUT TAPE2 IN IN ß ü SURR. R MULTI 8OHMS FM (75) OUT TAPE1 IN IN LD LD CENTER FRONT OUT REMOTE CONT. S-VIDEO SUB WOOFER R SPEAKERS L IN 8OHMS CD L R AUDIO L R TV TV VIDEO ñµ å FM Antenna AM Antenna ç Tape 1 Out Tape 1 In é Tape 2 Out Tape 2 In © CD IN Front R oe oe Multi IR ® Multi-Out ß Power Cable Switched AC Outlet ü Unswitched AC Outlet Remote IR In Remote IR Out î Front L Center ° Surround R ¬ Surround L µ Subwoofer Pre-Out ñ Pre-Outs ø 6 Channel Direct Input Multi Room Interface Rear Panel ­ Video Connections S FRONT MULTI OUT ANTENNA TV MONI AM GND FM (75) L G H B A P M R OUT VCR2 OUT IN OUT VCR2 IN TAPE2 IN OUT VCR1 OUT IN OUT VCR1 IN TAPE1 IN LD LD CD L AUDIO R TV TV T I J D C Q N S-VIDEO MAIN IN PRE OUT U K L E F R O L R 6-CH SURR. DIRECT INPUT CENTER CENTER 8OHMS R FRONT L SUB WOOFER LD DIGITAL IN AC OUTLETS 230V 50/60Hz) SURR. [. . . ] If the setting is not correct press the button again until the correct standard (PAL, SECAM or NTSC) is displayed. NOTE: Although the unit will switch "S" video signals, the on screen menus control system is NOT visible on the S video output. Press any of the navigational arrow buttons or the SELECT r button on the remote to bring the MAIN MENU up on your video screen. Press the ¤ button five times until the on screen > cursor is pointing to SET U P MENU. No more than 2 meters when rear-mounted speakers are used Optional Rear Wall Mounting At least 15 cm from ceiling At least 60 cm AVR80 manual 11/01/98 13:01 Side 17 System Configuration 17 ENGLISH 6. The on screen > cursor will already point toward this option when you select the menu. Press the < or > buttons q to choose one of these center channel options by moving the cursor: LARGE: Choose this option if you are 11. At SET UP MENU 2 (Figure #3) you are able to establish settings for multiroom operation and lock the control settings. You may skip these menus by pressing ¤ q until the on screen > cursor is next to RETURN TO MAIN MENU and pressing SELECT r. If multiroom operation will be used, the first option enables you to select the method used for volume control. With the > cursor pointing to MULTI RM VOL press the < or > buttons to choose one of these options: VARIABLE: Choose this option if MAIN I R S T M S N E U E U E P C R S L T UT O RO T TI U SEL UT S UND TONE ROO P ME OFF MENU ECTOR ELECTOR MODE M SEL:OFF NU MENU Figure 1 using either a THX Certified speaker system with a subwoofer or large size full range center channel speaker. SMALL: Choose this option if the SET CENTER UP MENU 1 A M O N F E RGE ALL NE F NU center speaker is small sized. NONE: Choose this option if you are not using a center channel speaker. When the center channel speaker selection is complete, press the ¤ button q to move to the next option. Each time, use the ADJUST / and ADJUST ¤ buttons w on the remote to change the volume level so that all speakers match, and press SPEAKER v to move to the next channel. NOTE: This test also serves as an opportunity to verify that all speakers are properly connected. If the sound from a speaker location does not match the location shown on the video and front panel displays, turn the AVR80 off and check the speaker wiring to make certain that the speaker is connected to the correct output terminals. When all speakers appear to have an equal volume, press the < button q on the remote to complete the procedure. NOTE: For a more accurate calibration of the speaker output levels perform the test outlined in steps 16 through 20 using a sound pressure level (SPL) meter. For calibration to THX standards, it is recommended that the output for each channel measure 75 dB (C-weighted, slow) on the meter. You have completed a basic set up and you are now ready to enjoy the finest in home theater and music listening enjoyment. settings as described above. UNLOCK: Choose this option to unlock the settings and enable them to be changed without going to this menu. When you have made your choice, press ¤ q and then SELECT r to return to the main menu. At this point the output levels for all channels will be set to a reference so that the sound level is the same from each speaker. This compensates for the differences between the speakers used and the distance each speaker is from your listening position. See the Advanced Features section later in this manual for information on delay settings. [. . . ] If the input source is changed from the remote room, the M ULT I indicator will remain lit, but stop flashing. If the AVR80 is turned off in the main listening room, the feed to the remote room will continue, although the MULTI indicator will now remain constantly illuminated. To turn off the feed to the remote room either while the AVR80 is still on, or after it is turned off, press the MULTI button on the front panel. If the MULTI button is pressed while the AVR80 is still on and the on screen video system is engaged, a warning message will appear on the video display (Figure #18) to remind you that people may still be listening to the system in the remote room location. Remote Room Operation In this option, the remote room feed is controlled by the use of an AVR80 compatible remote control. [. . . ]