User manual HARMAN KARDON AVR 5000

[. . . ] AVR 5000 Audio/Video Receiver OWNER'S MANUAL DTS DOLBY D PCM MP3 MUTE RDS PTY CT RT TA AUTO TUNED ST MEMORY PRESET SLEEP O O L O O 0C0 R O O OPTICAL 1 2 3 COAXIAL 1 2 3 ANALOG VMAx NF 5. 1 LOGIC 7 CM OSD LS O LFE RS O DIGITAL PRO LOGIC 3-STEREO 5 CH STEREO HALL 12 THEATER NIGHT MULTI ® Power for the Digital RevolutionTM Table of Contents 3 4 5 7 9 11 14 15 19 19 20 20 21 21 22 23 23 23 24 24 25 25 27 27 27 27 28 29 29 31 32 33 33 33 34 36 36 36 37 37 38 39 39 40 40 41 42 42 43 43 43 43 44 46 56 56 57 Introduction Safety Information Front Panel Controls Front Panel Information Display Rear Panel Connections Main Remote Control Functions Zone II Remote Control Functions Installation and Connections System Configuration Speaker Selection and Placement First Turn On and Use of OSD Settings to be Made With Each Input Used Input Setup Surround Setup Speaker Setup Adjustments for Other Inputs Making Settings independent of selected Input Delay Settings Night Mode Settings Output Level Adjustment Using EzSet Manual Output Level Adjustment Operation Basic Operation Source Selection Controls and Use of Headphones Surround Mode Chart Surround Mode Selection Digital Audio Playback Tape Recording Output Level Trim Adjustment 6-Channel Direct Input Memory Backup Tuner Operation RDS Operation Advanced Features Display Brightness Turn On Volume Level Semi OSD Settings Full-OSD Time Out Adjustment Multiroom Operation Programming the Remote Programming the Remote with Codes Code Readout Learning Codes From a Remote Macro Programming Programmed Device Function Volume Punch-Through Channel Control Punch-Through Transport Control Punch-Through Reassigning Device Control Selectors Resetting the Remote Memory Function List Setup Code Tables Troubleshooting Guide Processor Reset Technical Specifications Declaration of Conformity We, Harman Consumer International 2, route de Tours 72500 Château-du-Loir, FRANCE declare in own responsibility, that the product described in this owner's manual is in compliance with technical standards: EN 55013/6. 1990 EN 55020/12. 1994 EN 60065:1993 EN 61000-3-2/4. 1995 Carsten Olesen Harman Kardon Europe A/S 11/00 Typographical Conventions In order to help you use this manual with the remote control, front-panel controls and rear-panel connections, certain conventions have been used. EXAMPLE ­ (bold type) indicates a specific remote control or front-panel button, or rear-panel connection jack EXAMPLE ­ (OCR type) indicates a message that is visible on the front-panel information display 1 ­ (number in a square) indicates a specific front-panel control 0 ­ (number in a circle) indicates a rear-panel connection 0 ­ (number in an oval) indicates a button or indicator on the remote A ­ (letter in a square) indicates an indicator in the front-panel display å ­ (letter in an oval) indicates a button on the Zone II remote 2 TABLE OF CONTENTS Introduction Thank you for choosing Harman Kardon!With the purchase of a Harman Kardon AVR5000 you are about to begin many years of listening enjoyment. The AVR5000 has been custom designed to provide all the excitement and detail of movie sound tracks and every nuance of musical selections. [. . . ] Release the button when the Program/SPL Indicator 2 stops flashing and you hear the test noise from the front left speaker. At this point, the EzSet circuitry will take over, adjusting the output level of each channel so that when the process is complete all levels will be equal and at the set reference point. This process may take a few minutes, depending on the extent of adjustment required. During the adjustment you will see the location of the channel position being adjusted appear in both the on-screen display (if connected) and the Main Information Display Y, alternating with a readout of the output setting, relative to the reference volume level. As the adjustment proceeds, a few things will happen simultaneously: · The channel position being adjusted will flash in the Speaker/Channel Position Indicators Q. If the test noise is heard from a channel other than the one shown in the Indicator, there is an error in the speaker connections. If this is the case, press the Test Button 8 TWICE to stop the adjustment. Then, turn the unit off and verify that all speakers are connected to the proper Outputs DE. · When the front left channel is being set at the beginning of the process, EzSet will adjust the main volume level, as shown by the indication of the FRONT L L E V alternating in the onscreen display (if connected) and the Main Information Display Y with the volume indication. During the adjustment, the test tone may seem to pulse, or click, as EzSet changes the level. · As the other channels are set, the channel name and the adjustment offset will appear in the on-screen display (if connected) and the Main Information Display Y. While the level is changing, the Program/SPL Indicator 2 will change colors to reflect the output level in relation to the reference. A red indication shows that the level is too high, while an amber indication shows that the level is too low. When the Indicator is green, the level is correct, and the test noise will move to the next channel. · While adjustments are being made, the red LED under the AVR Selector 5 will flash. After the test noise has circulated once through each channel, it will send the tone to the front left channel once again, to finally adjust its output level. Upon completion of the front left channel adjustment, the Program/SPL Indicator will flash green three times and then go out. Manual Output Level Adjustment Output levels may also be adjusted manually, either to set them to a specific level with an SPL meter, or to make fine tuning adjustments to the levels obtained using the EzSet remote. Manual output level adjustment is most easily done through the OUTPUT ADJUST menu (Figure 7). If you are already at the main menu, press the ¤ buttons D until the onscreen > cursor is next to the OUTPUT ADJUST line. If you are not at the main menu, press the OSD button L to bring up the MASTER MENU (Figure 1), and then press the ¤ buttons D three times so that the on-screen > cursor is next to the Output adjust line. Press the Set button F to bring the OUTPUT ADJUST menu (Figure 7) to the screen. * F C F S S R R E R U U E OUTPUT O N O R R T N T N R R U T L ER T R RI LE RN ADJUST 0 0 0 0 0 U d d d d d B B B B B * : : IGHT: GHT : FT : TO MEN EFT Figure 7 As soon as the new menu appears, you will hear a test noise circulate from speaker to speaker in a clockwise direction around the room. [. . . ] To program the remote for Transport Control PunchThrough, follow these steps: 1. Press the Input Selector 4 for the device you wish to have the channel control associated with and the Mute button b at the same time until the red light illuminates, under the Input Selector 4 and the Program/ SPL Indicator 2 flashes amber. PROGRAMMING THE REMOTE 43 Function List No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 Button Name Power Off Power On Mute AVR DVD CD Tape VID 1 VID 2 VID 3 VID 4 Learn AM/FM 6 Ch. Select SPL Sleep Test TV Volume Up Surround Select Night Multi Room Volume Down Channel/Guide / AVR Function Power Off Power On Mute AVR Select DVD Input Select CD Input Select Tape Input Select Video 1 Select Video 2 Select Video 3 Select Video 4 Select Tuner Select 6 Ch Input Select SPL Sleep Test Tone Volume Up Surround Mode Select Night Mode Select Multi-Room Select Volume Down Channel Trim Move/Adjust Up Speaker Adjust Move/Adjust Left Set Move/Adjust Right Digital Input Select Move/Adjust Down Delay Adjust 1 2 3 4 5 6 7 8 Tuner Mode 9 0 Memory Tune Up Direct Tuner Entry Clear Preset Tune Up Tune Down OSD Preset Tune Down DVD Power Off Power On CD/CDR Power Off Power On 1 4 8 12 16 20 5 9 13 17 21 6 10 14 18 22 2 3 7 11 15 19 23 DVD Select CD Select 24 25 27 28 31 30 26 29 TV/DVD Volume Up Subtitle on/off Sub on/off Volume Down Title Up Menu Left Enter Right Open/Close Down Return 1 2 3 4 5 6 7 8 Chapter 9 0 Audio Angle Clear Slow Forward -/Input Select -/CDP Select -/CDR Select 32 33 37 41 45 49 53 57 60 34 38 42 46 50 54 58 61 63 35 39 43 47 51 55 36 40 44 48 52 56 59 62 Speaker/Menu fi Set fl Digital/Exit ¤ Intro/- 64 LIGHT 5000 Delay/Prev. [. . . ]