User manual HARMAN KARDON DPR 1005

[. . . ] ® Power for the Digital Revolution. ® DPR 1005 DIGITAL PATH RECEIVER OWNER'S MANUAL DPR 1005 DIGITAL PATH RECEIVER 3 4 4 5 8 11 15 16 19 19 19 20 22 22 24 26 27 27 28 30 30 30 30 30 31 31 32 35 35 35 36 37 37 37 37 37 38 39 39 39 40 41 41 41 42 42 43 44 46 47 48 49 51 51 52 Introduction Important Safety Information Unpacking Front-Panel Controls Rear-Panel Connections Main Remote Control Functions Zone II Remote Control Functions Installation and Connections System Configuration Speaker Placement System Setup Input Setup Audio Setup Surround Setup Speaker Setup Delay Settings Output Level Adjustment Using EzSet Manual Output Level Adjustment Operation Basic Operation Source Selection 6/8-Channel Direct Input Volume and Tone Control Surround Mode Selection Digital Audio Playback Surround Mode Chart Tuner Operation Tape Recording Front-Panel Connections Output Level Trim Adjustment Advanced Features Front-Panel Display Fade Display Brightness Turn-On Volume Level Semi-OSD Settings Full-OSD Time-Out Adjustment Multiroom Operation Multiroom Setup Surround Amplifier Channel Assignment Multiroom Operation Configuring the Remote Programming Remote Codes Preprogrammed Code Entry Automatic Code Entry Learning Commands Changing Devices Macro Programming Punch-Through Configuration EzSet Configuration Renaming Resetting the Remote Troubleshooting Guide Processor Reset Technical Specifications Typographical Conventions In order to help you use this manual with the remote control, front-panel controls and rear-panel connections, certain conventions have been used. EXAMPLE ­ (bold type) indicates a specific remote control or front-panel button, or rear-panel connection jack EXAMPLE ­ (OCR type) indicates a message that is visible on-screen or on the front-panel information display EXAMPLE ­ (Synchro type) indicates a message that is displayed on the remote control's LCD screen 1 ­ (number in a square) indicates a specific front-panel control A ­ (letter in a square) indicates a front-panel control that is behind the drop-down door ¡ ­ (number in a circle) indicates a rear-panel connection a ­ (number in an oval) indicates a button or indicator on the remote å ­ (letter in an oval) indicates a button on the Zone II remote See trademark acknowledgements on page 52. 2 TABLE OF CONTENTS INTRODUCTION Thank You for Choosing Harman Kardon® With the purchase of a Harman Kardon DPR 1005, you are about to begin many years of listening enjoyment. Thanks to its completely digital path system, the DPR 1005 is truly a receiver for the new millennium. The DPR 1005 has a wide range of features and options that accommodate virtually any combination of speakers, room size and program sources. [. . . ] You may also make these same adjustments with complete manual control over the channel being adjusted by pressing the //¤ Navigation Button o until the cursor is pointing to the TEST TONE SEQ line on the menu and then using the </> Navigation Button o to select MANUAL in the highlighted video. In the MANUAL mode, the test tone will also start immediately, but the tone will only be moved to another channel by pressing the //¤ Navigation Button o. When the manual sequencing mode is active, the tone is turned off by pressing the //¤ Navigation Button o until the cursor is pointing to the TEST TONE line and the </> Navigation Button o is then pressed to select OFF in the highlighted video. The DPR's EzSet feature may also be used as an SPL meter to assist in accurate setting of the output levels, when either the internal test tone or an external source such as a test disc is used. Press and hold the SPL Select Button 45 until the red LED under the Set Button q lights and the LCD screen in the remote changes to the display shown in Figure 10. Press the / Navigation Button o once to change the bottom line of the remote's LCD display to read MANUAL SPL as shown in Figure 14. SET SPKR LEVELS MANUAL SPL * F C F S C T T B L E R R H E E A CHANNEL :0 :0 :0 :0 NEL TO TO TO d d d d ADJUST * N A S S C N T T K B SBR B SBL B SL B SUB RESET NE SEQ NE MASTER :0 dB :0 dB :0 dB :0 dB :OFF ON :AUTO :OFF ON MENU Figure 13 Manual output level adjustment is most easily done through the CHANNEL ADJUST menu (Figure 13). If you are already at the MASTER MENU, press the ¤ Navigation Button o until the on-screen cursor is next to the CHANNEL ADJUST line. If you are not at the MASTER MENU, press the OSD Button U to bring up the MASTER MENU (Fig. 1), and then press the ¤ Navigation Button o until the on-screen cursor is next to the CHANNEL ADJUST line. Press the Set Button q to bring the CHANNEL ADJUST menu (Figure 13) to the screen. If desired, you may immediately use the //¤ Navigation Button o to select any channel for adjustment using an external source, such as a test disc, from which to judge the output levels. After the cursor is pointing to the channel to be adjusted, press the </> Navigation Button o to raise or lower the output level. However, before proceeding with any manual adjustment we recommend that you first use the DPR's internal test tone generator and automatic sequencer to send a tone to each channel so that you may verify that all speaker connections have been properly made. To turn the test tone on and have it automatically circulate among the channels where a speaker has previously been configured (see page 24), press the //¤ Navigation Button o until the cursor is pointing to the TEST TONE line on the menu. Next, press the </> Navigation Button o until AUTO SEQ is shown in highlighted video. At this time the test tone will immediately begin to circulate clockwise around the room, playing for two seconds in each speaker before switching to the next speaker position. The cursor will blink next to the active speaker to indicate which speaker the sound should be coming from. As the test noise circulates, listen to make certain that the sound comes from the speaker position shown in the Lower Display Line &. If the sound from a speaker location does NOT match the position indicated in the display, turn the DPR 1005 off using the Main Manual Output Level Adjustment Output levels may also be adjusted manually, either to set them to a specific level with an SPL meter, or to make fine tuning adjustments to the levels obtained using the EzSet remote. Figure 14 28 SYSTEM CONFIGURATION SYSTEM CONFIGURATION 3. Press the Set Button q within five seconds to activate the remote's manual mode, so that it functions as an SPL meter. The right corner of the bottom line of the remote's display will show the output level of the speakers as the test tone circulates. When you are finished with all adjustments, press the Clear Button 9 to return the remote to normal operation. [. . . ] message will appear in the upper line of the remote's LCD screen as shown in Figure 78. It may take a few minutes for the reset process to take place, and the length of time will vary depending on how much customization and programming has taken place. Please be patient; as long as the message appears in the display the remote is functioning properly. RESETTING. . . Figure 78 4. When the remote has been totally reset and returned to the factory default condition, a REMOTE RESET COMPLETE message will appear (Figure 79) briefly, and then the remote will return to normal operation. REMOTE RESET COMPLETE Figure 81 Figure 79 · The remote has a built-in backlight that may be activated by pressing the Light Button P. [. . . ]