User manual HARMAN KARDON FL8350

[. . . ] Harman Kardon FL8350 Compact Disc Changer 1 2 3 1 DISC fl 2 TRACK 3 4 MIN Skip Play Pause 5 SEC 1 6 11 16 2 7 12 17 3 8 13 18 4 9 14 19 5 10 15 20 4 5 Disc Skip Search Stop Random Open/Close Time Repeat Intro Clear Program Owner's Manual Staple or clip original invoice here. w Owner's Manual FL8350 Compact Disc Changer Table of Contents Introduction . 16 250 Crossways Park Drive Woodbury, NY 11797 ©1998 Harman Kardon, Incorporated Introduction 1 Thank you for choosing the Harman Kardon FL8350 CD changer. The FL8350 is an exceptionally well-engineered product that offers high performance and ease of use. [. . . ] (See page 14 for more information. ) p Disc Skip Button: Press this button to change to the next disc. If a disc position is empty, the FL8350 will automatically search for the next position that contains a disc. Installation 9 To prevent possible damage to your speakers and other components in your audio system, it is important that ALL components, including the FL8350 and receivers are turned off and unplugged from their AC power source when installing any new component. Using standard RCAto-RCA interconnect cords, connect the left and right Fixed Audio Output jacks on the rear panel to the CD input jacks on your receiver, surround processor or preamplifier. If your system includes an optional, external digital-to-analog converter, or if you are using a receiver or other processor that has the capability to decode PCM digital input signals, connect the Coaxial Digital Output jack TM to the Datastream Digital input on the decoder. Make certain to use a coaxialstyle interconnect cable, as standard audio cables will not perform as well. Install the two AA batteries supplied with the FL8350's remote by turning the remote over so that you are holding the bottom side up. Press lightly on the embossed arrow on the cover, and gently slide the cover towards you in the direction of the arrow. Insert the batteries inside the compartment, being careful to follow the + and ­ polarity indications at the bottom of the compartment. Replace the cover by placing it on the remote and sliding it back towards the top of the remote. NOTE: When replacing batteries it is always a good idea to replace both at the same time. When the unit will not be used for an extended period of time, it is also a good idea to remove the batteries so that the potential for corrosion or damage is avoided. Connect the power to a non-switched AC wall outlet, or to the accessory outlet on the rear of another audio device in your system and you are ready to go!NOTE: When using the accessory outlet on another product to power the FL8350 make certain that it has the ability to power a device that draws at least 20 watts of current in addition to the requirements of other devices that may be plugged into the accessory outlets. If you use a "switched" outlet, it is important to remember that the host product must be turned on in order for the FL8350 to operate. © Operation 10 Loading Discs To load a disc, first turn the FL8350 on using the Power Switch 1. Note that the Status Mode Indicator 2 will turn green and the Information Display Ó will illuminate. The word disc will flash in the Information Display, and the disc tray will automatically turn clockwise so that the FL8350 can sense which, if any, of the disc positions already have a disc. a, taking care to make certain that the space in front of the drawer is not obstructed. Note that if the drawer is blocked when attempting to open it, it will automatically close within five seconds to protect the mechanism. Load discs in the tray with the printed (label) side facing up towards you. When a 3" (8cm) disc is played, it should be carefully centered within the smaller ridges on the tray. When a 3" (8cm) is played, DO NOT place a standard 5" (12cm) disc over the smaller disc. Labeled surface Note that each disc position has a number embossed in the plastic tray. This corresponds to the position this disc will occupy for playback and programming. To make it easier to identify each disc's position, the disc position number for the holder space that is in the center of the disc tray will also appear in the Information Display when the disc drawer is open. [. . . ] Note that the program step indication on the right side of the Information Display will change to P-02. You may now select another disc and/or track for the next program step following the instruction shown above. Repeat this procedure for each program step until you have completed the desired programming. Press the Stop button % g to complete a program sequence, or press Play $ h to begin immediate play of a program sequence. [. . . ]