User manual HARMAN KARDON HD7300

[. . . ] a ­ (number in an oval) indicates a button or indicator on the remote. ¡ ­ (number in a circle) indicates a rear panel connection. 2 TABLE OF CONTENS Introduction Thank you for choosing Harman Kardon HD7300 CD player. The HD7300 is an exceptionally well-engineered product that offers high performance and ease of use. We ask that you take a few minutes to read through this Owner's Manual to familiarize yourself with the controls and functions. [. . . ] Using standard RCA-to-RCA interconnect cords, connect the left and right Audio Output jacks TM on the rear panel to the CD input jacks on your receiver, surround processor or preamplifier. If your system includes an optional external digital-to-analog converter, or if you are using a receiver or other processor that has the capability to decode PCM digital input signals, connect the Digital Output jack ¡ to the Coaxial Digital input on the decoder. Make certain to use a coaxial-style interconnect cable, as standard audio cables will not perform as well. Install two AA batteries by turning the remote over so that you are holding the bottom side up. Press lightly on the embossed arrow on the cover and gently slide the cover towards you in the direction of the arrow. Insert the batteries inside the compartment, being careful to follow the + and ­ polarity indications at the bottom of the compartment. Replace the cover by placing it on the remote and sliding it back towards the top of the remote. When the unit will not be used for an extended period of time, it is also a good idea to remove the batteries so that the potential for corrosion or damage is avoided. If the HD7300 is installed behind a cabinet or other obstruction that may block the path between the front-panel Remote Sensor 3 and the location of the remote, an optional external IR sensor may be used. Connect the sensor to the Remote IR-In Jack £ on the rear panel. This jack may also be connected to the IR-Output jack of another compatible Harman Kardon component or a compatible IRsystem- remote product. To play all of the tracks on the disc in order, press the Play button 4 9. To play all of the tracks in random order, press the Random button ) C and then the Play button 4 9. When Random is activated while programmed play is in use (see page 13), all programmed tracks will be played in random order. . You may also select a specific track by pressing the Skip buttons 7 7 until the wished track number is displayed (see page 12). The track may also be selected directly by entering the track number via the Numeric Controls 2, simply enter the track number by pressing the buttons that correspond to the desired track. Note that when a two-digit track number is being entered, the second digit of the number must be pressed within two seconds of the first digit. After the track is selected, press the Play button 4 9. Labeled Surface To retract the drawer back into the player after loading a disc, press the Open/Close button $ F. When the drawer is closed the display will indicate the total number of tracks on the disc and the total running time of the disc. The drawer will close and the disc will start playing the first track. 10 OPERATION Operation While the disc is playing, the track being played will show as a number in the middle of the display just below the word TRACK. The elapsed time of the track being played will also appear in the display (see figure page 10). As a disc plays, the track numbers will change, and the time will reset to at the start of each new track. [. . . ] Repeat this procedure for each program step until you have completed the desired programming. Press the Stop button 5 A once to complete a program sequence, or press Play 4 9 to begin immediate play of a program sequence. If the maximum of 32 program steps is reached, the program-step indication at the right side of the Information Display will go out, and the disc and track that have been programmed as the first program step will be shown. Checking Program Contents To check the contents of a program while the unit is stopped at first note that the PROGRAM indicator is lit (otherwise press Program) and the program step indication P-01 just below the PROGRAM indicator is not lit (otherwise press Stop once). Each time the Check button E is pressed now, the Information Display will step through each of the programmed tracks. PROGRAMMED PLAY OPERATION 13 Repeat Play Operation Repeat Play The HD7300's programming system enables you to repeat either a single track, the entire disc (respectively all programmed tracks) or a specially programmed passage that you select. [. . . ]